Raspberry Pi simulator for GPIO, in Python with gpiozero
The Raspberry Pi 4 Model B, the Raspberry Pi 5 and the Raspberry Pi Zero 2 W, from their 40-pin header. Your main.py runs in a Python engine in the page, and gpiozero and RPi.GPIO drive the header as they do on a real Pi, on the simulated clock. There is no Linux here, and this page says plainly what that leaves out.
- 9modellenen çevre birimi alanları
- 9çalışmaya hazır projeler
- Gerçek zamanlıkendi makinende

Neler modelleniyor
Kartın kendi sözleşme belgesinden alındı ve sade bir dille yazıldı; eksik olanlar yanında.
Modellenen
- Üst bilgi
- All 40 pins in their real order, named by BCM number, with BOARD numbering mapped to them
- Güç
- 3V3 on pins 1 and 17, 5V on pins 2 and 4, and the eight grounds
- GPIO
- GPIO 0 to 27 at 3.3 V logic, as inputs with their 50 k pulls or as outputs, with the SoC’s power-on pulls and the 1.8 k pull-ups on GPIO 2 and 3
- gpiozero 2.0.1
- LED, PWMLED, RGBLED, Button, Buzzer, Servo, AngularServo, DistanceSensor, MotionSensor, LineSensor and more, on the lgpio pin factory
- RPi.GPIO 0.7.1
- BCM and BOARD, setup, output, input, PWM, add_event_detect, wait_for_edge and cleanup, with the library’s own warnings and errors
- Zaman
- time.sleep(1) is one simulated second; edge callbacks run at the time of the edge
- The Pi 5
- RPi.GPIO fails there with the error a real Pi 5 gives, and gpiozero works
- I2C ve SPI
- /dev/i2c-1 and /dev/spidev0.0 and 0.1, with smbus, smbus2, spidev and gpiozero’s MCP3008, at the speed of the bus and with the errors a Pi gives
- The Serial Monitor
- print() and tracebacks, input(), and Ctrl-C as KeyboardInterrupt
Modellenmeyen
- Linux. There is no kernel, no desktop, no terminal, no sudo and no file system beyond the project’s files.
- pip and apt. Only the modules that come with the board can be imported.
- Networking: no Wi-Fi, Ethernet or Bluetooth, and no socket or requests.
- Kamera, ekran, HDMI ve ses.
- The I2C bus’s speed setting and clock stretching: I2C runs at Raspberry Pi OS’s default 100 kHz.
- Threads. gpiozero’s callbacks, blink() and PWM run without them.
- CPython itself: the engine is MicroPython, so a few details of the language differ (isinstance(True, int) is False). Programs that drive the pins run unchanged.
Birini aç ve Çalıştır'a bas
Bunların her biri düzenleyicide burada çizildiği gibi açılır.
Every built-in project on the Raspberry Pi
Her birinin çalışan devresi, kodu ve parça listesiyle kendi sayfası var.
Bu kartı kullanan dersler
Her biri aynı kartta çalışan bir devreyle biter.
Sorular
Ücretsiz mi?
Evet. Her kart ve her parça ücretsiz plandadır, hesap gerekmez.
Bu bir Raspberry Pi emülatörü mü?
No. There is no Arm core and no Linux. Your Python runs in a Python engine in the page, and its gpiozero and RPi.GPIO drive the header. Everything a circuit can see of a Pi is here; the operating system is not.
Why does RPi.GPIO fail on the Pi 5?
Because it fails on a real Pi 5: the pins are on the RP1 chip, which RPi.GPIO 0.7.1 cannot find, and GPIO.setup raises "Cannot determine SOC peripheral base address". Use gpiozero, which works on all three boards.
Bir kütüphaneyi pip install ile kurabilir miyim?
Hayır. Bir kütüphanenin .py dosyasını kendi sekmesi olarak ekle ve main.py'den import et; bu, düz Python ile yazılmış kütüphaneler için çalışır.
Programım gerçek bir Pi üzerinde çalışır mı?
Evet, Raspberry Pi OS ile birlikte geldiği haliyle gpiozero veya RPi.GPIO ile. Gerçek bir Pi'de zamanlama daha gevşektir: yazılım PWM'i orada titrer, burada titremez.
Diğer kartlar
Bunların her biri bugün çalışıyor ve her biri ücretsiz.
Daha kısa bir tanıtım mı arıyorsun? Şuraya bak: the Raspberry Pi simulator page.
Gerçek bellek haritasında 160 MHz'de çalışan bir RISC-V çip.
16 MHz'de çalışan ATmega328P'li klasik Arduino.
Uno'nun çipi, breadboard'a sığan küçük bir kartta.
54 dijital pini ve dört seri portu olan büyük Arduino.
Çipi USB seriyi kendisi yapan, Uno biçiminde bir kart.
31 pinli ve WiFi'si simüle edilen ikinci bir RISC-V kartı.
240 MHz'de, WiFi simülasyonlu klasik ESP32.
USB seri ve RGB LED'ye sahip, 240 MHz'de çalışan ESP32-S3.
Kendi Python kodunla dene
gpiozero veya RPi.GPIO ile main.py yaz ve Çalıştır'a bas. Kurulum gerekmez, hesap gerekmez.