Raspberry Pi simulator for GPIO, in Python with gpiozero
The Raspberry Pi 4 Model B, the Raspberry Pi 5 and the Raspberry Pi Zero 2 W, from their 40-pin header. Your main.py runs in a Python engine in the page, and gpiozero and RPi.GPIO drive the header as they do on a real Pi, on the simulated clock. There is no Linux here, and this page says plainly what that leaves out.
- 9area periferal dimodelkan
- 9proyek siap dijalankan
- Waktu nyatadi mesinmu sendiri

Apa yang dimodelkan
Diambil dari dokumen kontrak board itu sendiri dan ditulis dengan kata-kata sederhana, beserta apa yang belum ada di sampingnya.
Dimodelkan
- Header
- All 40 pins in their real order, named by BCM number, with BOARD numbering mapped to them
- Daya
- 3V3 on pins 1 and 17, 5V on pins 2 and 4, and the eight grounds
- GPIO
- GPIO 0 to 27 at 3.3 V logic, as inputs with their 50 k pulls or as outputs, with the SoC’s power-on pulls and the 1.8 k pull-ups on GPIO 2 and 3
- gpiozero 2.0.1
- LED, PWMLED, RGBLED, Button, Buzzer, Servo, AngularServo, DistanceSensor, MotionSensor, LineSensor and more, on the lgpio pin factory
- RPi.GPIO 0.7.1
- BCM and BOARD, setup, output, input, PWM, add_event_detect, wait_for_edge and cleanup, with the library’s own warnings and errors
- Waktu
- time.sleep(1) is one simulated second; edge callbacks run at the time of the edge
- The Pi 5
- RPi.GPIO fails there with the error a real Pi 5 gives, and gpiozero works
- I2C dan SPI
- /dev/i2c-1 and /dev/spidev0.0 and 0.1, with smbus, smbus2, spidev and gpiozero’s MCP3008, at the speed of the bus and with the errors a Pi gives
- The Serial Monitor
- print() and tracebacks, input(), and Ctrl-C as KeyboardInterrupt
Tidak dimodelkan
- Linux. There is no kernel, no desktop, no terminal, no sudo and no file system beyond the project’s files.
- pip and apt. Only the modules that come with the board can be imported.
- Networking: no Wi-Fi, Ethernet or Bluetooth, and no socket or requests.
- Kamera, layar, HDMI, dan audio.
- The I2C bus’s speed setting and clock stretching: I2C runs at Raspberry Pi OS’s default 100 kHz.
- Threads. gpiozero’s callbacks, blink() and PWM run without them.
- CPython itself: the engine is MicroPython, so a few details of the language differ (isinstance(True, int) is False). Programs that drive the pins run unchanged.
Buka salah satu dan tekan Jalankan
Masing-masing terbuka di editor persis seperti yang digambar di sini.
Every built-in project on the Raspberry Pi
Masing-masing punya halaman sendiri dengan rangkaian yang berjalan, kode, dan daftar komponen.
Tutorial yang memakai board ini
Masing-masing berakhir dengan rangkaian yang berjalan, di board yang sama.
Pertanyaan
Apakah gratis?
Ya. Setiap board dan setiap komponen ada di paket gratis, tanpa akun.
Apakah ini emulator Raspberry Pi?
No. There is no Arm core and no Linux. Your Python runs in a Python engine in the page, and its gpiozero and RPi.GPIO drive the header. Everything a circuit can see of a Pi is here; the operating system is not.
Why does RPi.GPIO fail on the Pi 5?
Because it fails on a real Pi 5: the pins are on the RP1 chip, which RPi.GPIO 0.7.1 cannot find, and GPIO.setup raises "Cannot determine SOC peripheral base address". Use gpiozero, which works on all three boards.
Bisakah aku pip install sebuah library?
Tidak. Tambahkan file .py library sebagai tab tersendiri dan impor dari main.py, yang berfungsi untuk library yang ditulis dengan Python murni.
Apakah programku akan jalan di Pi sungguhan?
Ya, dengan gpiozero atau RPi.GPIO karena keduanya sudah ada di Raspberry Pi OS. Timing di Pi sungguhan lebih longgar: software PWM bergoyang di sana, tapi tidak di sini.
Board lainnya
Semua ini berjalan hari ini, dan semuanya gratis.
Cari pengenalan yang lebih singkat? Lihat the Raspberry Pi simulator page.
Chip RISC-V di 160 MHz, dengan peta memori yang asli.
Arduino klasik, dengan ATmega328P yang berjalan di 16 MHz.
Chip Uno di board kecil yang muat di breadboard.
Arduino besar, dengan 54 pin digital dan empat port serial.
Board berbentuk Uno yang chip-nya mengurus serial USB sendiri.
Board RISC-V kedua, dengan 31 pin dan WiFi simulasi.
ESP32 klasik di 240 MHz, dengan WiFi simulasi.
ESP32-S3 di 240 MHz, dengan serial USB dan LED RGB.
Coba dengan Python-mu sendiri
Tulis main.py dengan gpiozero atau RPi.GPIO lalu tekan Jalankan. Tanpa instalasi apa pun dan tanpa perlu akun.