Raspberry Pi simulator for GPIO, in Python with gpiozero
The Raspberry Pi 4 Model B, the Raspberry Pi 5 and the Raspberry Pi Zero 2 W, from their 40-pin header. Your main.py runs in a Python engine in the page, and gpiozero and RPi.GPIO drive the header as they do on a real Pi, on the simulated clock. There is no Linux here, and this page says plainly what that leaves out.
- 9مناطق طرفية تمت نمذجتها
- 9مشاريع جاهزة للتشغيل
- زمن حقيقيعلى جهازك أنت

ما الذي يُحاكى
مأخوذ من وثيقة العقد الخاصة باللوحة ومكتوب بكلمات بسيطة، مع ما هو ناقص بجانبه.
مُحاكى
- الشريط العلوي
- All 40 pins in their real order, named by BCM number, with BOARD numbering mapped to them
- التغذية
- 3V3 on pins 1 and 17, 5V on pins 2 and 4, and the eight grounds
- GPIO
- GPIO 0 to 27 at 3.3 V logic, as inputs with their 50 k pulls or as outputs, with the SoC’s power-on pulls and the 1.8 k pull-ups on GPIO 2 and 3
- gpiozero 2.0.1
- LED, PWMLED, RGBLED, Button, Buzzer, Servo, AngularServo, DistanceSensor, MotionSensor, LineSensor and more, on the lgpio pin factory
- RPi.GPIO 0.7.1
- BCM and BOARD, setup, output, input, PWM, add_event_detect, wait_for_edge and cleanup, with the library’s own warnings and errors
- الوقت
- time.sleep(1) is one simulated second; edge callbacks run at the time of the edge
- The Pi 5
- RPi.GPIO fails there with the error a real Pi 5 gives, and gpiozero works
- I2C و SPI
- /dev/i2c-1 and /dev/spidev0.0 and 0.1, with smbus, smbus2, spidev and gpiozero’s MCP3008, at the speed of the bus and with the errors a Pi gives
- The Serial Monitor
- print() and tracebacks, input(), and Ctrl-C as KeyboardInterrupt
غير مُحاكى
- Linux. There is no kernel, no desktop, no terminal, no sudo and no file system beyond the project’s files.
- pip and apt. Only the modules that come with the board can be imported.
- Networking: no Wi-Fi, Ethernet or Bluetooth, and no socket or requests.
- الكاميرا والشاشة وHDMI والصوت.
- The I2C bus’s speed setting and clock stretching: I2C runs at Raspberry Pi OS’s default 100 kHz.
- Threads. gpiozero’s callbacks, blink() and PWM run without them.
- CPython itself: the engine is MicroPython, so a few details of the language differ (isinstance(True, int) is False). Programs that drive the pins run unchanged.
افتح واحدة واضغط «تشغيل»
كل واحد منها يفتح في المحرر تماماً كما هو مرسوم هنا.
Every built-in project on the Raspberry Pi
لكل منها صفحة خاصة بالدائرة العاملة والكود وقائمة القطع.
دروس تستخدم هذه اللوحة
كل درس ينتهي بدائرة تعمل، على هذه اللوحة نفسها.
الأسئلة
هل هو مجاني؟
نعم. كل لوحة وكل قطعة في الباقة المجانية، بلا حاجة إلى حساب.
هل هذا محاكٍ لجهاز Raspberry Pi؟
No. There is no Arm core and no Linux. Your Python runs in a Python engine in the page, and its gpiozero and RPi.GPIO drive the header. Everything a circuit can see of a Pi is here; the operating system is not.
Why does RPi.GPIO fail on the Pi 5?
Because it fails on a real Pi 5: the pins are on the RP1 chip, which RPi.GPIO 0.7.1 cannot find, and GPIO.setup raises "Cannot determine SOC peripheral base address". Use gpiozero, which works on all three boards.
هل يمكنني تثبيت مكتبة باستخدام pip؟
لا. أضف ملف .py الخاص بالمكتبة كتبويب مستقل واستورده من main.py، وهذا يعمل مع المكتبات المكتوبة بلغة Python الخالصة.
هل سيعمل برنامجي على جهاز Pi حقيقي؟
نعم، مع gpiozero أو RPi.GPIO كما تأتي مع نظام Raspberry Pi OS. التوقيت على جهاز حقيقي أقل دقة: PWM البرمجي يتذبذب هناك ولا يتذبذب هنا.
اللوحات الأخرى
كل واحدة منها تعمل اليوم، وكلها مجانية.
تبحث عن مقدمة أقصر؟ انظر the Raspberry Pi simulator page.
شريحة RISC-V بسرعة 160 MHz، على خريطة الذاكرة الحقيقية.
Arduino الكلاسيكية، مع ATmega328P بسرعة 16 MHz.
شريحة Uno على لوحة صغيرة تُركّب على لوحة التجارب.
Arduino الكبيرة، بـ 54 طرفًا رقميًا وأربعة منافذ تسلسلية.
لوحة بشكل Uno، شريحتها تتولى اتصال USB التسلسلي بنفسها.
لوحة RISC-V ثانية، بـ 31 طرفًا و WiFi مُحاكى.
ESP32 الكلاسيكية بسرعة 240 MHz، مع WiFi مُحاكى.
ESP32-S3 بسرعة 240 MHz، مع USB تسلسلي و RGB LED.
جرّبه بكود Python الخاص بك
اكتب main.py باستخدام gpiozero أو RPi.GPIO ثم اضغط «تشغيل». لا شيء لتثبيته ولا حاجة إلى حساب.