All paths

Build a scrolling LED sign

Four chained LED matrices driven bit by bit, your own 5x7 font, smooth scrolling, typed messages, auto brightness and an on-air sign.

Arduino Uno R3Free6 lessons5 h3 chapters1,654 XPMaker · Intermediate+150 XP

0 of 6 done

What you will build

3 projects, built step by step

6 lessons in 3 chapters, about 5 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.

Chapter 1 project

Fonts

Store a 5x7 font as bytes in flash, draw a word with it, and see every character as hex and as a picture of its pixels.

Open it in the simulator
Chapter 2 project

Messages

Take new messages typed over serial, swap them in at the end of a pass, tidy the input, and see how the same code takes them over WiFi on an ESP32.

Open it in the simulator
Chapter 3 project

Project: an on-air sign

Put it all together: scrolling messages and automatic brightness, and a red button that puts a steady ON AIR on the sign at full brightness.

Open it in the simulator
The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

Matrices and fonts

Drive a chain of four MAX7219s by hand and draw with a font made of bytes.

  1. Open174 XP

    Chained matrices

    Drive four MAX7219 chips in a daisy chain by hand: wake them, run a display test of all 256 LEDs, and light one module at a time with No-Op packets.

    0 of 4 steps

  2. ProjectLocked348 XP

    Fonts

    Store a 5x7 font as bytes in flash, draw a word with it, and see every character as hex and as a picture of its pixels.

    0 of 4 steps

4 questions, graded as you go.
Chapter 2

Scrolling and messages

A strip of columns, a moving window and messages from the serial port.

  1. Locked174 XP

    Scrolling

    Turn a message into one long strip of columns, slide a 32-column window along it on a timer, and change the speed while it runs.

    0 of 4 steps

  2. ProjectLocked410 XP

    Messages

    Take new messages typed over serial, swap them in at the end of a pass, tidy the input, and see how the same code takes them over WiFi on an ESP32.

    0 of 5 steps

4 questions, graded as you go.
Chapter 3

On air

Brightness that follows the room, and a sign for the studio door.

  1. Locked174 XP

    Brightness

    Set the sign's brightness from a light sensor: average eight readings, map them to the chip's sixteen steps, dim at night and bright in the sun.

    0 of 4 steps

  2. ProjectLocked374 XP

    Project: an on-air sign

    Put it all together: scrolling messages and automatic brightness, and a red button that puts a steady ON AIR on the sign at full brightness.

    0 of 5 steps

3 questions, graded as you go.
Syllabus

Every lesson in the course

All 6 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

Matrices and fonts

  1. Chained matricesDrive four MAX7219 chips in a daisy chain by hand: wake them, run a display test of all 256 LEDs, and light one module at a time with No-Op packets.
  2. FontsStore a 5x7 font as bytes in flash, draw a word with it, and see every character as hex and as a picture of its pixels.
Chapter 2

Scrolling and messages

  1. ScrollingTurn a message into one long strip of columns, slide a 32-column window along it on a timer, and change the speed while it runs.
  2. MessagesTake new messages typed over serial, swap them in at the end of a pass, tidy the input, and see how the same code takes them over WiFi on an ESP32.
Chapter 3

On air

  1. BrightnessSet the sign's brightness from a light sensor: average eight readings, map them to the chip's sixteen steps, dim at night and bright in the sun.
  2. Project: an on-air signPut it all together: scrolling messages and automatic brightness, and a red button that puts a steady ON AIR on the sign at full brightness.
Keep going

The next course on your track

Build a scrolling LED sign is part of the maker track, a ladder of courses from zero to expert.

Next course

Build a smart beehive

Build a hive monitor beekeepers can trust: weight trends, brood temperature, hive sound, a swarm watch and LoRa reports.

Open the next course
Track

Maker track

Follow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.

See every course on the track
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Build a scrolling LED sign

Is Build a scrolling LED sign free?

Yes. All 6 lessons of Build a scrolling LED sign are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Arduino Uno R3?

No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Build a scrolling LED sign take?

About 5 hours: 6 lessons in 3 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: Fonts, Messages and Project: an on-air sign.

Where do I start?

With "Chained matrices", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.