Continuity check
Prove an igniter is in the clips and unbroken with a sense current about a thousand times too small to light it: 5 V, a 4.7k resistor and an analog pin.
Open it in the simulatorBuild the launch box a club rocket range runs on: a safety key, an arm code, a continuity check, a countdown, every abort and a misfire lockout.
0 of 6 done
6 lessons in 3 chapters, about 6 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.
Prove an igniter is in the clips and unbroken with a sense current about a thousand times too small to light it: 5 V, a 4.7k resistor and an analog pin.
Open it in the simulatorThree ways to stop a launch, each named on the monitor: the abort key, the safety key and a lost igniter. Then make sure the only way back is a fresh start.
Open it in the simulatorRun a launch day from the table: check the pad, arm with the club code, count down, fly two rockets in a row and read back the log. Then make the box your own.
Open it in the simulatorEach lesson opens when the one before it is done, and each chapter ends in a project.
A key, a code, and proof the igniter is there.
Two things arm a launch box, and they cannot happen together by accident: a safety key and a code. Wire the key so it cuts the fire relay in hardware, then read it in software too.
0 of 5 steps
Prove an igniter is in the clips and unbroken with a sense current about a thousand times too small to light it: 5 V, a 4.7k resistor and an analog pin.
0 of 6 steps
Five, four, three, two, one, and every way to say no.
Press A and count down from five with a beep a second on the TM1637, then pull the relay in for exactly one second and watch the igniter glow.
0 of 6 steps
Three ways to stop a launch, each named on the monitor: the abort key, the safety key and a lost igniter. Then make sure the only way back is a fresh start.
0 of 5 steps
Misfires, the 60 second rule, and a full launch day.
The rules a real range runs on, built into the box: a power-up self-test, no arming with the key left in, a liftoff check, and the 60 second misfire wait.
0 of 6 steps
Run a launch day from the table: check the pad, arm with the club code, count down, fly two rockets in a row and read back the log. Then make the box your own.
0 of 6 steps
Finish every lesson and pass every chapter quiz and Mokxi issues a certificate with your name, verified on its own page.
Certificate of Completion
This is to certify that
Your Name
has successfully completed the course
Build a rocket launch controller
Covering Safe, then armed, Count down, or stop and On the range.
6 lessons · about 6 hours of study
Finish the course and earn a verifiable certificate with your name, a QR code and a link for LinkedIn. Certificates come with Pro, and the 7-day trial is free.
All 6 lessons, in order, each with what it covers. Any of them opens in the editor right away.
Build a rocket launch controller is part of the maker track, a ladder of courses from zero to expert.
Read a rotary dial pulse by pulse, add a hook switch and a DFPlayer, and turn an old phone into a jukebox that rings you back.
Open the next courseFollow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.
See every course on the trackEvery lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.
An Uno, a keypad (4x4), a four-digit display (TM1637), a relay module and a filament lamp: a launch box that arms, checks and counts down.
Open the kitPick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kitYes. All 6 lessons of Build a rocket launch controller are free and run in your browser, with nothing to install and no parts to buy before you start.
No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.
About 6 hours: 6 lessons in 3 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.
Each chapter ends in a project that puts it together: Continuity check, Abort and Project: a club launch box.
With "Arming keys", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.