Lesson plan

Build a rocket launch controller lesson plan

Build the launch box a club rocket range runs on: a safety key, an arm code, a continuity check, a countdown, every abort and a misfire lockout.

3 chapters, 6 lessons, about 6 hours, on the Arduino Uno R3. Every lesson runs in the browser, with nothing to install.

The unit

Objectives and materials

By the end, students can

  • A key, a code, and proof the igniter is there.
  • Five, four, three, two, one, and every way to say no.
  • Misfires, the 60 second rule, and a full launch day.

Materials for the whole unit

  • Arduino Uno R3
  • Battery: AA, coin cell, LiPo
  • Buzzer
  • Filament lamp
  • Four-digit display, TM1637
  • Full-size breadboard
  • Keypad, 4x4
  • LED x 2
  • Relay module
  • Resistor x 3
  • Slide switch x 2

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 2 h

Safe, then armed

A key, a code, and proof the igniter is there.

LessonTimeWhat students do
Arming keysTwo things arm a launch box, and they cannot happen together by accident: a safety key and a code. Wire the key so it cuts the fire relay in hardware, then read it in software too.55 min
  1. Meet the launch box
  2. Turn the key
  3. Try a wrong code
  4. Arm it
  5. Pull the key
Continuity checkProve an igniter is in the clips and unbroken with a sense current about a thousand times too small to light it: 5 V, a 4.7k resistor and an analog pin.65 min
  1. Read the igniter
  2. A current too small to fire
  3. Empty the clips
  4. Refuse to arm
  5. Clip in and arm
  6. Lose it while armed

Materials

  • Arduino Uno R3
  • Battery: AA, coin cell, LiPo
  • Buzzer
  • Filament lamp
  • Four-digit display, TM1637
  • Full-size breadboard
  • Keypad, 4x4
  • LED x 2
  • Relay module
  • Resistor x 3
  • Slide switch x 2

Check for understanding

Each student finishes "Continuity check" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Lose it while armed".

Chapter 2. About 2 h

Count down, or stop

Five, four, three, two, one, and every way to say no.

LessonTimeWhat students do
CountdownPress A and count down from five with a beep a second on the TM1637, then pull the relay in for exactly one second and watch the igniter glow.65 min
  1. Arm the pad
  2. Start the count
  3. Fire
  4. The igniter lights
  5. One second, and no more
  6. Key out mid-count
AbortThree ways to stop a launch, each named on the monitor: the abort key, the safety key and a lost igniter. Then make sure the only way back is a fresh start.55 min
  1. Abort with the keypad
  2. A fresh start, every time
  3. Pull the key mid-count
  4. Lose the igniter mid-count
  5. Abort, then fly

Materials

  • Arduino Uno R3
  • Battery: AA, coin cell, LiPo
  • Buzzer
  • Filament lamp
  • Four-digit display, TM1637
  • Full-size breadboard
  • Keypad, 4x4
  • LED x 2
  • Relay module
  • Resistor x 3
  • Slide switch x 2

Check for understanding

Each student finishes "Abort" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Abort, then fly".

Chapter 3. About 2 h 10 min

On the range

Misfires, the 60 second rule, and a full launch day.

LessonTimeWhat students do
Range safetyThe rules a real range runs on, built into the box: a power-up self-test, no arming with the key left in, a liftoff check, and the 60 second misfire wait.65 min
  1. The self-test
  2. Never power up live
  3. A clean launch
  4. A misfire
  5. The 60 second rule
  6. Keep a log
Project: a club launch boxRun a launch day from the table: check the pad, arm with the club code, count down, fly two rockets in a row and read back the log. Then make the box your own.65 min
  1. Set up the pad
  2. Range is clear: arm
  3. Count it down
  4. Liftoff
  5. Next pad
  6. Make it your club's

Materials

  • Arduino Uno R3
  • Battery: AA, coin cell, LiPo
  • Buzzer
  • Filament lamp
  • Four-digit display, TM1637
  • Full-size breadboard
  • Keypad, 4x4
  • LED x 2
  • Relay module
  • Resistor x 3
  • Slide switch x 2

Check for understanding

Each student finishes "Project: a club launch box" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Make it your club's".

Your class

Teach this unit as a class

Start a class from this course and its 6 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.