All paths

Build a guitar controller

A rhythm game guitar on a Pro Micro in three short lessons: frets and a strum bar that never double-strums, a whammy and star power, and your own config.

SparkFun Pro MicroFree3 lessons1 h2 chapters606 XPMaker · Intermediate+150 XP

0 of 3 done

What you will build

One project, built step by step

3 lessons in 2 chapters, about 1 hour on a simulated SparkFun Pro Micro. Free, in your browser, every step checked by the simulator.

Chapter 1 project

The whammy and star power

A whammy pot calibrated with a rest point and a deadzone, and a ball tilt switch that turns the neck going up into a button.

Open it in the simulator
The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

The inputs

Frets, a strum bar, a whammy and a tilt switch, each read cleanly.

  1. Open156 XP

    Frets and the strum bar

    Five fret buttons and two strum switches on a Pro Micro, each on its own pin with the pull-up on, and a lockout that turns a bouncing strum into one note.

    0 of 4 steps

  2. ProjectLocked312 XP

    The whammy and star power

    A whammy pot calibrated with a rest point and a deadzone, and a ball tilt switch that turns the neck going up into a button.

    0 of 4 steps

Chapter 2

Your guitar

The config block, left-handed play, and the step to a real board.

  1. Locked138 XP

    Make it your guitar

    The config block at the top of the sketch: pins, left-handed play, lockouts and calibration, then what changes when you flash a real Pro Micro.

    0 of 4 steps

Syllabus

Every lesson in the course

All 3 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

The inputs

  1. Frets and the strum barFive fret buttons and two strum switches on a Pro Micro, each on its own pin with the pull-up on, and a lockout that turns a bouncing strum into one note.
  2. The whammy and star powerA whammy pot calibrated with a rest point and a deadzone, and a ball tilt switch that turns the neck going up into a button.
Chapter 2

Your guitar

  1. Make it your guitarThe config block at the top of the sketch: pins, left-handed play, lockouts and calibration, then what changes when you flash a real Pro Micro.
Keep going

The next course on your track

Build a guitar controller is part of the maker track, a ladder of courses from zero to expert.

Next course

Build a laser sword

A light saber style sword in three builds: a blade that ignites, motion you can hear, then the whole hilt with a sound font.

Open the next course
Track

Maker track

Follow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.

See every course on the track
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Build a guitar controller

Is Build a guitar controller free?

Yes. All 3 lessons of Build a guitar controller are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real SparkFun Pro Micro?

No. Every lesson runs on a simulated SparkFun Pro Micro with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Build a guitar controller take?

About 1 hour: 3 lessons in 2 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: The whammy and star power.

Where do I start?

With "Frets and the strum bar", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.