All paths

Build a greenhouse controller

Build the controller that runs a greenhouse: climate and VPD, fans with hysteresis, safe watering, a photoperiod, schedules and a season log.

Arduino Uno R3Free6 lessons5 h3 chapters1,685 XPMaker · Intermediate+150 XP

0 of 6 done

What you will build

3 projects, built step by step

6 lessons in 3 chapters, about 5 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.

Chapter 1 project

Fans and vents

Run a fan with hysteresis: on at 28 C, off only under 26 C, faster as it gets hotter, and on for damp air too.

Open it in the simulator
Chapter 2 project

Lights

Run a grow light on a 16 hour photoperiod from a DS3231, with its state worked out from the clock so a power cut cannot leave it wrong.

Open it in the simulator
Chapter 3 project

Project: a season log

The whole controller: climate, fan, scheduled watering and lights, an hourly log line, and a summary of every day.

Open it in the simulator
The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

The air

Read the climate, and move air when it goes wrong.

  1. Open174 XP

    Climate sensing

    Read a greenhouse's air with an SHT31 and turn temperature and humidity into the one number growers steer by: the vapor pressure deficit.

    0 of 4 steps

  2. ProjectLocked410 XP

    Fans and vents

    Run a fan with hysteresis: on at 28 C, off only under 26 C, faster as it gets hotter, and on for damp air too.

    0 of 5 steps

4 questions, graded as you go.
Chapter 2

Water and light

A pump with limits, and a grow light on the clock.

  1. Locked205 XP

    Watering

    Water from a soil probe through an active-low relay and a pump: start under 35 percent, stop at 50, never run longer than 10 seconds, and catch an empty reservoir.

    0 of 5 steps

  2. ProjectLocked348 XP

    Lights

    Run a grow light on a 16 hour photoperiod from a DS3231, with its state worked out from the clock so a power cut cannot leave it wrong.

    0 of 4 steps

4 questions, graded as you go.
Chapter 3

Run the season

Schedules from a table, then the whole house with a log.

  1. Locked174 XP

    Schedules

    Water only in morning and evening windows from a schedule table, work out the next event from the clock, and keep the photoperiod going.

    0 of 4 steps

  2. ProjectLocked374 XP

    Project: a season log

    The whole controller: climate, fan, scheduled watering and lights, an hourly log line, and a summary of every day.

    0 of 5 steps

3 questions, graded as you go.
Syllabus

Every lesson in the course

All 6 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

The air

  1. Climate sensingRead a greenhouse's air with an SHT31 and turn temperature and humidity into the one number growers steer by: the vapor pressure deficit.
  2. Fans and ventsRun a fan with hysteresis: on at 28 C, off only under 26 C, faster as it gets hotter, and on for damp air too.
Chapter 2

Water and light

  1. WateringWater from a soil probe through an active-low relay and a pump: start under 35 percent, stop at 50, never run longer than 10 seconds, and catch an empty reservoir.
  2. LightsRun a grow light on a 16 hour photoperiod from a DS3231, with its state worked out from the clock so a power cut cannot leave it wrong.
Chapter 3

Run the season

  1. SchedulesWater only in morning and evening windows from a schedule table, work out the next event from the clock, and keep the photoperiod going.
  2. Project: a season logThe whole controller: climate, fan, scheduled watering and lights, an hourly log line, and a summary of every day.
Keep going

The next course on your track

Build a greenhouse controller is part of the maker track, a ladder of courses from zero to expert.

Next course

Build a high-altitude balloon tracker

Build the payload that rides a balloon to 30 km: GPS in flight mode, pressure and cold, LoRa tracking, a flight log, a cutdown and a whole simulated flight.

Open the next course
Track

Maker track

Follow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.

See every course on the track
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Build a greenhouse controller

Is Build a greenhouse controller free?

Yes. All 6 lessons of Build a greenhouse controller are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Arduino Uno R3?

No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Build a greenhouse controller take?

About 5 hours: 6 lessons in 3 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: Fans and vents, Lights and Project: a season log.

Where do I start?

With "Climate sensing", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.