All paths

Satellite tracker

Aim a dish with a stepper and a servo, predict a pass from an orbit model, then track it across the sky.

Arduino Uno R3Free4 lessons4 h2 chapters1,424 XPMaker · Advanced+250 XP

0 of 4 done

Start the course freePoint by stepsBuild it as a kitRetails for about $40, free on Mokxi.Lesson plan for teachers
What you will build

2 projects, built step by step

4 lessons in 2 chapters, about 4 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.

Chapter 1 project

Azimuth and elevation

Add a servo for elevation and point at any spot in the sky with two angles, on a short tour that ends straight overhead.

Open it in the simulator
Chapter 2 project

Track a pass

Fly the whole tracker: predict, pre-position, count down on the LCD, follow the satellite from rise to set, and flip over the top of a high pass.

Open it in the simulator
The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

Pointing

Turn and tip a dish to any spot in the sky.

  1. Open212 XP

    Point by steps

    Aim a dish with a 28BYJ-48 stepper: 4096 half steps to a turn, a quarter turn per press, and an LCD that says where it points.

    0 of 4 steps

  2. ProjectLocked424 XP

    Azimuth and elevation

    Add a servo for elevation and point at any spot in the sky with two angles, on a short tour that ends straight overhead.

    0 of 4 steps

Chapter 2

Orbits and tracking

Predict where the satellite will be, then follow it.

  1. Locked212 XP

    Predict a pass

    Model a circular orbit, put yourself on a turning Earth, and turn the difference into a table of azimuth and elevation from rise to set.

    0 of 4 steps

  2. ProjectLocked576 XP

    Track a pass

    Fly the whole tracker: predict, pre-position, count down on the LCD, follow the satellite from rise to set, and flip over the top of a high pass.

    0 of 6 steps

Syllabus

Every lesson in the course

All 4 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

Pointing

  1. Point by stepsAim a dish with a 28BYJ-48 stepper: 4096 half steps to a turn, a quarter turn per press, and an LCD that says where it points.
  2. Azimuth and elevationAdd a servo for elevation and point at any spot in the sky with two angles, on a short tour that ends straight overhead.
Chapter 2

Orbits and tracking

  1. Predict a passModel a circular orbit, put yourself on a turning Earth, and turn the difference into a table of azimuth and elevation from rise to set.
  2. Track a passFly the whole tracker: predict, pre-position, count down on the LCD, follow the satellite from rise to set, and flip over the top of a high pass.
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

The kit for this course

Satellite Tracker Kit

An Uno, a stepper motor (28BYJ-48 with ULN2003) and a hobby servo: a tracker that follows satellites across the sky.

Open the kit
Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Satellite tracker

Is Satellite tracker free?

Yes. All 4 lessons of Satellite tracker are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Arduino Uno R3?

No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Satellite tracker take?

About 4 hours: 4 lessons in 2 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: Azimuth and elevation and Track a pass.

Where do I start?

With "Point by steps", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.