All paths

Linear power supplies

From a transformer's AC to clean DC: bridge rectifiers and ripple, Zener regulators, the LM317, low-dropout regulators, heat and heatsinks, and a dual bench supply you design down to every part.

Free7 lessons5 h7 chapters1,448 XPElectrical · Intermediate+150 XP

0 of 7 done

What you will build

0 projects, built step by step

7 lessons in 7 chapters, about 5 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

Transformer to DC

A secondary, a bridge and a smoothing capacitor.

  1. Open205 XP

    Transformer to DC

    From the wall to a DC rail: a transformer's 12 V secondary, a bridge rectifier that flips every half cycle the same way, the two diode drops it costs, and the smoothing capacitor that turns humps into a rail.

    0 of 5 steps

3 questions, graded as you go.
Chapter 2

Ripple

I / (2 f C), on an AC range and a scope.

  1. Locked205 XP

    Ripple

    The sawtooth a reservoir capacitor leaves on the rail: reading it on an AC range, the I / (2 f C) rule, a bigger capacitor, a heavier load, and why the lowest point of the ripple is the number that matters.

    0 of 5 steps

3 questions, graded as you go.
Chapter 3

Zener regulators

A resistor, a Zener, and the load they can carry.

  1. Locked205 XP

    Zener regulators

    The simplest regulator: a resistor and a Zener on the raw rail, how well it holds 5 V as the load changes, the current it wastes, and the load it cannot carry.

    0 of 5 steps

3 questions, graded as you go.
Chapter 4

LM317

Two resistors set the voltage; headroom keeps it.

  1. Locked205 XP

    The LM317

    An adjustable regulator from three legs and two resistors: 5 V from 240 and 720 ohms, a new voltage from a new resistor, how little ripple gets through, and the headroom it needs.

    0 of 5 steps

3 questions, graded as you go.
Chapter 5

LDO dropout

How low the input can go.

  1. Locked205 XP

    LDO dropout

    How close to its output a regulator's input can fall: a 7805 that gives up 2 V short, an AMS1117 that needs 1.1 V, and an MCP1700 that runs a 3.3 V board from a single lithium cell to the end.

    0 of 5 steps

3 questions, graded as you go.
Chapter 6

Heatsinks

Watts, degrees per watt, and cutting the heat.

  1. Locked187 XP

    Heatsinks

    A linear regulator turns the voltage it drops into heat: measure it, work out the junction temperature from the datasheet's degrees per watt, see what a heatsink buys, and cut the heat at the source.

    0 of 5 steps

3 questions, graded as you go.
Chapter 7

Boss build

A dual bench supply.

  1. Locked236 XP

    Boss: a bench supply

    A small dual bench supply from the course's parts: a 24 V transformer, a bridge and a reservoir, an adjustable LM317 output, and a fixed 5 V output fed through a Zener pre-regulator. Set it, load it, check its ripple and headroom, and give it the voltage you need.

    0 of 6 steps

3 questions, graded as you go.
Syllabus

Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

Transformer to DC

  1. Transformer to DCFrom the wall to a DC rail: a transformer's 12 V secondary, a bridge rectifier that flips every half cycle the same way, the two diode drops it costs, and the smoothing capacitor that turns humps into a rail.
Chapter 2

Ripple

  1. RippleThe sawtooth a reservoir capacitor leaves on the rail: reading it on an AC range, the I / (2 f C) rule, a bigger capacitor, a heavier load, and why the lowest point of the ripple is the number that matters.
Chapter 3

Zener regulators

  1. Zener regulatorsThe simplest regulator: a resistor and a Zener on the raw rail, how well it holds 5 V as the load changes, the current it wastes, and the load it cannot carry.
Chapter 4

LM317

  1. The LM317An adjustable regulator from three legs and two resistors: 5 V from 240 and 720 ohms, a new voltage from a new resistor, how little ripple gets through, and the headroom it needs.
Chapter 5

LDO dropout

  1. LDO dropoutHow close to its output a regulator's input can fall: a 7805 that gives up 2 V short, an AMS1117 that needs 1.1 V, and an MCP1700 that runs a 3.3 V board from a single lithium cell to the end.
Chapter 6

Heatsinks

  1. HeatsinksA linear regulator turns the voltage it drops into heat: measure it, work out the junction temperature from the datasheet's degrees per watt, see what a heatsink buys, and cut the heat at the source.
Chapter 7

Boss build

  1. Boss: a bench supplyA small dual bench supply from the course's parts: a 24 V transformer, a bridge and a reservoir, an adjustable LM317 output, and a fixed 5 V output fed through a Zener pre-regulator. Set it, load it, check its ripple and headroom, and give it the voltage you need.
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Linear power supplies

Is Linear power supplies free?

Yes. All 7 lessons of Linear power supplies are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does Linear power supplies take?

About 5 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Transformer to DC", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.