Lesson plan

Linear power supplies lesson plan

From a transformer's AC to clean DC: bridge rectifiers and ripple, Zener regulators, the LM317, low-dropout regulators, heat and heatsinks, and a dual bench supply you design down to every part.

7 chapters, 7 lessons, about 5 hours, no board. Every lesson runs in the browser, with nothing to install.

The unit

Objectives and materials

By the end, students can

  • A secondary, a bridge and a smoothing capacitor.
  • I / (2 f C), on an AC range and a scope.
  • A resistor, a Zener, and the load they can carry.
  • Two resistors set the voltage; headroom keeps it.
  • How low the input can go.
  • Watts, degrees per watt, and cutting the heat.
  • A dual bench supply.

Materials for the whole unit

  • Capacitor x 3
  • DC voltage source
  • Diode x 4
  • LM317 regulator
  • Mains transformer, 230 V or 120 V to 12 V
  • Multimeter x 3
  • Oscilloscope
  • Resistor x 6
  • Signal generator
  • Voltage regulator
  • Zener diode

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 40 min

Transformer to DC

A secondary, a bridge and a smoothing capacitor.

LessonTimeWhat students do
Transformer to DCFrom the wall to a DC rail: a transformer's 12 V secondary, a bridge rectifier that flips every half cycle the same way, the two diode drops it costs, and the smoothing capacitor that turns humps into a rail.40 min
  1. Run it: the secondary
  2. A bridge: every half the same way
  3. Smooth it
  4. The diodes' share
  5. A light load

Materials

  • Capacitor
  • Diode x 4
  • Mains transformer, 230 V or 120 V to 12 V
  • Multimeter
  • Resistor x 2
  • Signal generator

Check for understanding

Each student finishes "Transformer to DC" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A light load".

Chapter 2. About 40 min

Ripple

I / (2 f C), on an AC range and a scope.

LessonTimeWhat students do
RippleThe sawtooth a reservoir capacitor leaves on the rail: reading it on an AC range, the I / (2 f C) rule, a bigger capacitor, a heavier load, and why the lowest point of the ripple is the number that matters.40 min
  1. Run it: a 12 V adapter
  2. Read the ripple
  3. A bigger capacitor
  4. A heavier load
  5. A light load

Materials

  • Capacitor
  • Diode x 4
  • Multimeter x 2
  • Oscilloscope
  • Resistor
  • Signal generator

Check for understanding

Each student finishes "Ripple" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A light load".

Chapter 3. About 40 min

Zener regulators

A resistor, a Zener, and the load they can carry.

LessonTimeWhat students do
Zener regulatorsThe simplest regulator: a resistor and a Zener on the raw rail, how well it holds 5 V as the load changes, the current it wastes, and the load it cannot carry.40 min
  1. Run it: 5 V from 15
  2. The current it wastes
  3. Load it
  4. Past its limit
  5. Resize the resistor

Materials

  • Capacitor
  • Diode x 4
  • Multimeter x 2
  • Resistor x 2
  • Signal generator
  • Zener diode

Check for understanding

Each student finishes "Zener regulators" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Resize the resistor".

Chapter 4. About 40 min

LM317

Two resistors set the voltage; headroom keeps it.

LessonTimeWhat students do
The LM317An adjustable regulator from three legs and two resistors: 5 V from 240 and 720 ohms, a new voltage from a new resistor, how little ripple gets through, and the headroom it needs.40 min
  1. Run it: 5 V
  2. Set 9 V
  3. Ripple rejection
  4. Headroom
  5. Down to 3.3 V

Materials

  • Capacitor x 2
  • Diode x 4
  • LM317 regulator
  • Multimeter x 2
  • Resistor x 3
  • Signal generator

Check for understanding

Each student finishes "The LM317" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Down to 3.3 V".

Chapter 5. About 40 min

LDO dropout

How low the input can go.

LessonTimeWhat students do
LDO dropoutHow close to its output a regulator's input can fall: a 7805 that gives up 2 V short, an AMS1117 that needs 1.1 V, and an MCP1700 that runs a 3.3 V board from a single lithium cell to the end.40 min
  1. Run it: plenty of headroom
  2. The battery sags
  3. A lower dropout
  4. One cell to the end
  5. Even an LDO runs out

Materials

  • Capacitor
  • DC voltage source
  • Multimeter
  • Resistor
  • Voltage regulator

Check for understanding

Each student finishes "LDO dropout" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Even an LDO runs out".

Chapter 6. About 40 min

Heatsinks

Watts, degrees per watt, and cutting the heat.

LessonTimeWhat students do
HeatsinksA linear regulator turns the voltage it drops into heat: measure it, work out the junction temperature from the datasheet's degrees per watt, see what a heatsink buys, and cut the heat at the source.40 min
  1. Run it: half an amp
  2. Where 3.5 W goes
  3. Degrees per watt
  4. Cut it at the source
  5. Too far

Materials

  • Capacitor
  • DC voltage source
  • Multimeter x 3
  • Resistor
  • Voltage regulator

Check for understanding

Each student finishes "Heatsinks" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Too far".

Chapter 7. About 50 min

Boss build

A dual bench supply.

LessonTimeWhat students do
Boss: a bench supplyA small dual bench supply from the course's parts: a 24 V transformer, a bridge and a reservoir, an adjustable LM317 output, and a fixed 5 V output fed through a Zener pre-regulator. Set it, load it, check its ripple and headroom, and give it the voltage you need.50 min
  1. Run it: the raw rail
  2. The adjustable output
  3. The fixed 5 V
  4. Find the fixed output's limit
  5. Set it to 24 V
  6. Make it yours

Materials

  • Capacitor x 3
  • Diode x 4
  • LM317 regulator
  • Mains transformer, 230 V or 120 V to 12 V
  • Multimeter x 3
  • Resistor x 6
  • Signal generator
  • Voltage regulator
  • Zener diode

Check for understanding

Each student finishes "Boss: a bench supply" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Make it yours".

Your class

Teach this unit as a class

Start a class from this course and its 7 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.