Lesson plan

Troubleshooting control circuits lesson plan

The motor starter an industrial electrician gets called to: read the ladder, find opens with the voltage method and hopscotch, tell coils from contacts, handle overloads and intermittents, and fix a dead conveyor with three faults on it.

7 chapters, 7 lessons, about 6 hours, no board. Every lesson runs in the browser, with nothing to install.

The unit

Objectives and materials

By the end, students can

  • Rails, rungs, wire numbers, and where 24 V should be.
  • Measure across each device: the open reads the whole supply.
  • One lead on L2, the other hopping until the voltage vanishes.
  • An open coil, a burnt contact under load, and a welded one.
  • Read a trip, set the dial from the motor, never reset into a jam.
  • Why a blink is a stop, the wiggle test and the loose terminal.
  • Three faults, one dangerous, and a pull-cord stop to finish.

Materials for the whole unit

  • Bench power supply
  • Capacitor
  • DC motor
  • DPDT relay x 3
  • Limit switch, lever microswitch x 3
  • Multimeter x 2
  • Pushbutton
  • Resistor x 2
  • Slide switch x 2

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 50 min

Reading the ladder

Rails, rungs, wire numbers, and where 24 V should be.

LessonTimeWhat students do
Reading the ladderA 24 V conveyor starter drawn as a ladder: rails, rungs, wire numbers, a coil and its contacts. Run it, start it, stop it, and read where the voltage sits on each wire.50 min
  1. Run it: the bench
  2. Press START
  3. Wire 3 stays alive
  4. Press STOP: wire 2 goes dead
  5. The load takes it all
  6. Read it like a drawing

Materials

  • Bench power supply
  • Capacitor
  • DC motor
  • DPDT relay x 3
  • Limit switch, lever microswitch x 2
  • Multimeter
  • Pushbutton
  • Resistor
  • Slide switch

Check for understanding

Each student finishes "Reading the ladder" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Read it like a drawing".

Chapter 2. About 50 min

The voltage method

Measure across each device: the open reads the whole supply.

LessonTimeWhat students do
The voltage methodThe conveyor will not start. Measure across each device on the dead rung: closed ones read nothing, the coil reads nothing because no current flows, and the open reads the whole supply.50 min
  1. The ticket: power first
  2. Across a closed contact
  3. Across the coil: nothing
  4. Across the open: everything
  5. Fix it
  6. Verify

Materials

  • Bench power supply
  • Capacitor
  • DC motor
  • DPDT relay x 3
  • Limit switch, lever microswitch x 2
  • Multimeter
  • Pushbutton
  • Resistor
  • Slide switch

Check for understanding

Each student finishes "The voltage method" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Verify".

Chapter 3. About 50 min

Hopscotch testing

One lead on L2, the other hopping until the voltage vanishes.

LessonTimeWhat students do
Hopscotch testingOne lead parked on L2, the other hopping from wire number to wire number along the rung. Voltage is there until you jump past the open; then it is gone.50 min
  1. Park one lead
  2. Hop to wire 2
  3. Through START
  4. The voltage vanishes
  5. Fix wire 3
  6. Verify by hopping

Materials

  • Bench power supply
  • Capacitor
  • DC motor
  • DPDT relay x 3
  • Limit switch, lever microswitch x 2
  • Multimeter
  • Pushbutton
  • Resistor
  • Slide switch

Check for understanding

Each student finishes "Hopscotch testing" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Verify by hopping".

Chapter 4. About 50 min

Failed coils and contacts

An open coil, a burnt contact under load, and a welded one.

LessonTimeWhat students do
Failed coils and contactsA coil with 24 V across it that never pulls in, then a contactor that runs the motor slow: an open coil proved on the ohms range, and a burnt contact found by measuring it under load.50 min
  1. Full voltage, no click
  2. Lock out, ohm it, replace it
  3. It runs, slowly
  4. Measure the contact under load
  5. New contacts
  6. The other contact failure: welded

Materials

  • Bench power supply
  • Capacitor
  • DC motor
  • DPDT relay x 3
  • Limit switch, lever microswitch x 2
  • Multimeter
  • Pushbutton
  • Resistor x 2
  • Slide switch

Check for understanding

Each student finishes "Failed coils and contacts" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "The other contact failure: welded".

Chapter 5. About 50 min

Overloads

Read a trip, set the dial from the motor, never reset into a jam.

LessonTimeWhat students do
OverloadsAn overload that trips the instant START is pressed, then a jam that trips it for real. Read the trip, set the dial from the motor's current, measure the running amps, and never reset into a jam.50 min
  1. Tripped on start
  2. Read the dial
  3. Measure the running current
  4. Jam the belt
  5. Clear it, then reset
  6. Setting a real overload

Materials

  • Bench power supply
  • Capacitor
  • DC motor
  • DPDT relay x 3
  • Limit switch, lever microswitch x 2
  • Multimeter x 2
  • Pushbutton
  • Resistor
  • Slide switch

Check for understanding

Each student finishes "Overloads" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Setting a real overload".

Chapter 6. About 55 min

Intermittents

Why a blink is a stop, the wiggle test and the loose terminal.

LessonTimeWhat students do
IntermittentsA conveyor that stops on its own once a shift and runs fine when you get there. Why a split-second open stops a seal-in circuit for good, the wiggle test, and catching the loose terminal on the meter.55 min
  1. Runs fine when you look
  2. Why a blink is a stop
  3. Catch it on the meter
  4. Hop past it
  5. Terminate it properly
  6. Prove it with a wiggle
  7. The usual suspects

Materials

  • Bench power supply
  • Capacitor
  • DC motor
  • DPDT relay x 3
  • Limit switch, lever microswitch x 2
  • Multimeter
  • Pushbutton
  • Resistor
  • Slide switch x 2

Check for understanding

Each student finishes "Intermittents" on their own, without opening the hints. The simulator checks 7 of its 7 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "The usual suspects".

Chapter 7. About 1 h 5 min

Boss: fix a dead conveyor

Three faults, one dangerous, and a pull-cord stop to finish.

LessonTimeWhat students do
Boss: fix a dead conveyorA repair ticket on the packing line: the conveyor is dead. Three faults stand between you and a running belt, one of them dangerous. Find each with the meter, fix it, verify, then add a pull-cord stop.65 min
  1. The ticket
  2. Fault 1: find the open
  3. Fix wire 4
  4. Fault 2: runs only while held
  5. Verify the latch
  6. Fault 3: STOP does not stop
  7. Remove the jumper
  8. Make it yours: a pull-cord stop

Materials

  • Bench power supply
  • Capacitor
  • DC motor
  • DPDT relay x 3
  • Limit switch, lever microswitch x 3
  • Multimeter
  • Pushbutton
  • Resistor
  • Slide switch

Check for understanding

Each student finishes "Boss: fix a dead conveyor" on their own, without opening the hints. The simulator checks 8 of its 8 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Make it yours: a pull-cord stop".

Your class

Teach this unit as a class

Start a class from this course and its 7 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.