Ring toss sensors
Put a light gate at the foot of each peg, count a ring only when the beam stays cut, catch the ones that bounce off, and score a turn.
Open it in the simulatorTouch targets, light gates and an eight-digit display: whack-a-target, ring toss, skee-ball, high scores and a booth that pays out tickets.
0 of 6 done
6 lessons in 3 chapters, about 5 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.
Put a light gate at the foot of each peg, count a ring only when the beam stays cut, catch the ones that bounce off, and score a turn.
Open it in the simulatorKeep a high score that survives the power going off: EEPROM read at power-up, written only when beaten, and shown as H1 on the display.
Open it in the simulatorRun the whole booth: attract mode, a 30 second clock, tickets and a high score in EEPROM, then make it your own and build it for real.
Open it in the simulatorEach lesson opens when the one before it is done, and each chapter ends in a project.
Touch targets and light gates: whack-a-target and a fair ring toss.
Read three touch targets, learn how a touch sensor feels a finger, and build a whack-a-target round with hits, misses and a time limit.
0 of 6 steps
Put a light gate at the foot of each peg, count a ring only when the beam stays cut, catch the ones that bounce off, and score a turn.
0 of 5 steps
Skee-ball lanes, a scoreboard and a high score that survives the night.
A light gate under each hole worth 10, 30 and 50: catch every fast ball on its edge, show balls and score on a MAX7219, nine balls a game.
0 of 5 steps
Keep a high score that survives the power going off: EEPROM read at power-up, written only when beaten, and shown as H1 on the display.
0 of 4 steps
Tickets, a jackpot, a game clock and attract mode: a booth that runs itself.
Turn a score into tickets with a table and a jackpot, then count them out one chirp at a time like a real ticket machine.
0 of 5 steps
Run the whole booth: attract mode, a 30 second clock, tickets and a high score in EEPROM, then make it your own and build it for real.
0 of 5 steps
All 6 lessons, in order, each with what it covers. Any of them opens in the editor right away.
Build carnival games is part of the maker track, a ladder of courses from zero to expert.
Four lit arcade buttons, a host and a buzzer: judge who pressed first, lock out cheats, keep score and run a real quiz night.
Open the next courseFollow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.
See every course on the trackEvery lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.
An Uno, a photo interrupter (slot), a touch sensor (TTP223) and an eight-digit display (MAX7219): carnival games that score and pay out tickets.
Open the kitPick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kitYes. All 6 lessons of Build carnival games are free and run in your browser, with nothing to install and no parts to buy before you start.
No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.
About 5 hours: 6 lessons in 3 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.
Each chapter ends in a project that puts it together: Ring toss sensors, Scores and Project: a game booth.
With "Whack targets", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.