All paths

Build your own bench tools

A frequency counter, a capacitance meter, a resistor tester, a battery tester and a DAC signal generator, then all five in one LCD box.

Arduino Uno R3Free6 lessons5 h3 chapters1,902 XPMaker · Intermediate+150 XP

0 of 6 done

What you will build

3 projects, built step by step

6 lessons in 3 chapters, about 5 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.

Chapter 1 project

A capacitance meter

Charge a capacitor through 10k, time how long it takes to reach 63.2% of the supply, and that time is R x C: a capacitance meter from one resistor and a stopwatch.

Open it in the simulator
Chapter 2 project

A battery tester

Run an AA cell into a 10 ohm load through an INA219, add up the milliamp-hours every second, and stop at 0.9 V with the capacity it really delivered.

Open it in the simulator
Chapter 3 project

One box, five tools

Put all five instruments behind one 16x2 LCD and a MENU button: frequency, capacitance, resistance, battery and a DAC staircase, the same numbers as the lessons before.

Open it in the simulator
The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

Measure time

Count edges in a gate and time a capacitor charging.

  1. Open236 XP

    A frequency counter

    Count the rising edges of a signal for exactly one second with an interrupt, and see how the gate sets the resolution and where the meter stops being right.

    0 of 6 steps

  2. ProjectLocked410 XP

    A capacitance meter

    Charge a capacitor through 10k, time how long it takes to reach 63.2% of the supply, and that time is R x C: a capacitance meter from one resistor and a stopwatch.

    0 of 5 steps

4 questions, graded as you go.
Chapter 2

Parts and power

Resistors by divider and batteries by the milliamp-hour.

  1. Locked205 XP

    A component tester

    Read an unknown resistor with a known 10k and the ADC, work out its color bands, and see why a two-resistor meter is sharp in the middle and blunt at the ends.

    0 of 5 steps

  2. ProjectLocked410 XP

    A battery tester

    Run an AA cell into a 10 ohm load through an INA219, add up the milliamp-hours every second, and stop at 0.9 V with the capacity it really delivered.

    0 of 5 steps

5 questions, graded as you go.
Chapter 3

Signals and the box

A DAC that makes voltages, then all five tools in one box.

  1. Locked205 XP

    A signal generator

    Set any voltage from 0 to 5 V in 1.2 mV steps with an MCP4725 DAC, then step a 32-point sine table out of it at 5 Hz.

    0 of 5 steps

  2. ProjectLocked436 XP

    One box, five tools

    Put all five instruments behind one 16x2 LCD and a MENU button: frequency, capacitance, resistance, battery and a DAC staircase, the same numbers as the lessons before.

    0 of 6 steps

4 questions, graded as you go.
Syllabus

Every lesson in the course

All 6 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

Measure time

  1. A frequency counterCount the rising edges of a signal for exactly one second with an interrupt, and see how the gate sets the resolution and where the meter stops being right.
  2. A capacitance meterCharge a capacitor through 10k, time how long it takes to reach 63.2% of the supply, and that time is R x C: a capacitance meter from one resistor and a stopwatch.
Chapter 2

Parts and power

  1. A component testerRead an unknown resistor with a known 10k and the ADC, work out its color bands, and see why a two-resistor meter is sharp in the middle and blunt at the ends.
  2. A battery testerRun an AA cell into a 10 ohm load through an INA219, add up the milliamp-hours every second, and stop at 0.9 V with the capacity it really delivered.
Chapter 3

Signals and the box

  1. A signal generatorSet any voltage from 0 to 5 V in 1.2 mV steps with an MCP4725 DAC, then step a 32-point sine table out of it at 5 Hz.
  2. One box, five toolsPut all five instruments behind one 16x2 LCD and a MENU button: frequency, capacitance, resistance, battery and a DAC staircase, the same numbers as the lessons before.
Keep going

The next course on your track

Build your own bench tools is part of the maker track, a ladder of courses from zero to expert.

Next course

Build a cat laser toy

Your first robot: a pan and tilt laser turret on two servos that plays with a cat on its own, with random glides, tuned speed and pauses, real laser eye safety, a session timer, and a toy at the end of every game.

Open the next course
Track

Maker track

Follow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.

See every course on the track
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Build your own bench tools

Is Build your own bench tools free?

Yes. All 6 lessons of Build your own bench tools are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Arduino Uno R3?

No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Build your own bench tools take?

About 5 hours: 6 lessons in 3 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: A capacitance meter, A battery tester and One box, five tools.

Where do I start?

With "A frequency counter", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.