All paths

Battery management systems

What a BMS measures and why: chemistries, series strings, balancing, state of charge, protection and charging, ending in a 2S pack monitor you wire and set for your own pack.

Free7 lessons6 h7 chapters1,765 XPElectrical · Advanced+250 XP

0 of 7 done

Start the course freeChemistries: what a cell's voltage tells youLesson plan for teachers
What you will build

0 projects, built step by step

7 lessons in 7 chapters, about 6 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

Chemistries

Full, empty and nominal, and the resistance inside a cell.

  1. Open288 XP

    Chemistries: what a cell's voltage tells you

    One 18650 on a meter and a 4 ohm load: 4.2 V full, 3.0 V empty, the sag under load from internal resistance, a small pouch that sags more, and how lithium-ion, LiFePO4, NiMH and lead-acid compare.

    0 of 6 steps

4 questions, graded as you go.
Chapter 2

Series strings

2S adds voltages, and the weakest cell sets the end.

  1. Locked250 XP

    Series strings: 2S and the weakest cell

    Two 18650s in series make 8.4 V: the same current through both, a mismatched cell, and a weak cell that hits empty while the pack voltage still looks healthy, which is why a BMS measures every cell.

    0 of 5 steps

4 questions, graded as you go.
Chapter 3

Balancing

A bleed resistor and a MOSFET per cell.

  1. Locked250 XP

    Balancing: bleeding the high cell

    A 2S pack 0.24 V out of balance: a bleed resistor and an AO3400A drain the high cell alone, watch it come down to its neighbor, work out the heat, and balance the bottom cell too.

    0 of 5 steps

3 questions, graded as you go.
Chapter 4

State of charge

Volts against counted coulombs, and a capacity that fades.

  1. Locked212 XP

    State of charge: volts and coulombs

    An Uno watches a 2S pack with a cell tap, a divider and an INA219: state of charge from the lowest cell's voltage, and by counting the charge that flows out, which agree until the capacity is wrong.

    0 of 4 steps

3 questions, graded as you go.
Chapter 5

Protection

Overcurrent, undervoltage and imbalance, latched until reset.

  1. Locked250 XP

    Protection: the MOSFET that says no

    The pack monitor opens its low-side MOSFET on overcurrent, latches until reset, cuts off a weak cell at 3.0 V, takes a higher undervoltage setting, and warns of imbalance.

    0 of 5 steps

4 questions, graded as you go.
Chapter 6

Charging profiles

Constant current, constant voltage and the end of charge.

  1. Locked227 XP

    Charging profiles: CC, then CV, then stop

    A TP4056 charges one 18650: a constant 1 A, the cell voltage climbing, the switch to constant 4.2 V as the current tapers, and the standby lamp at the end, with the rules for charging lithium safely.

    0 of 5 steps

4 questions, graded as you go.
Chapter 7

Boss build

A 2S monitor with your own limits.

  1. Locked288 XP

    Boss: a 2S pack monitor

    Wire the protection MOSFET, then run a 2S monitor that watches each cell, counts the charge out, trips on overcurrent and undervoltage, and takes the limits you set for your own pack.

    0 of 6 steps

3 questions, graded as you go.
Syllabus

Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

Chemistries

  1. Chemistries: what a cell's voltage tells youOne 18650 on a meter and a 4 ohm load: 4.2 V full, 3.0 V empty, the sag under load from internal resistance, a small pouch that sags more, and how lithium-ion, LiFePO4, NiMH and lead-acid compare.
Chapter 2

Series strings

  1. Series strings: 2S and the weakest cellTwo 18650s in series make 8.4 V: the same current through both, a mismatched cell, and a weak cell that hits empty while the pack voltage still looks healthy, which is why a BMS measures every cell.
Chapter 3

Balancing

  1. Balancing: bleeding the high cellA 2S pack 0.24 V out of balance: a bleed resistor and an AO3400A drain the high cell alone, watch it come down to its neighbor, work out the heat, and balance the bottom cell too.
Chapter 4

State of charge

  1. State of charge: volts and coulombsAn Uno watches a 2S pack with a cell tap, a divider and an INA219: state of charge from the lowest cell's voltage, and by counting the charge that flows out, which agree until the capacity is wrong.
Chapter 5

Protection

  1. Protection: the MOSFET that says noThe pack monitor opens its low-side MOSFET on overcurrent, latches until reset, cuts off a weak cell at 3.0 V, takes a higher undervoltage setting, and warns of imbalance.
Chapter 6

Charging profiles

  1. Charging profiles: CC, then CV, then stopA TP4056 charges one 18650: a constant 1 A, the cell voltage climbing, the switch to constant 4.2 V as the current tapers, and the standby lamp at the end, with the rules for charging lithium safely.
Chapter 7

Boss build

  1. Boss: a 2S pack monitorWire the protection MOSFET, then run a 2S monitor that watches each cell, counts the charge out, trips on overcurrent and undervoltage, and takes the limits you set for your own pack.
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Battery management systems

Is Battery management systems free?

Yes. All 7 lessons of Battery management systems are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does Battery management systems take?

About 6 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Chemistries: what a cell's voltage tells you", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.