Lesson plan

Battery management systems lesson plan

What a BMS measures and why: chemistries, series strings, balancing, state of charge, protection and charging, ending in a 2S pack monitor you wire and set for your own pack.

7 chapters, 7 lessons, about 6 hours, no board. Every lesson runs in the browser, with nothing to install.

The unit

Objectives and materials

By the end, students can

  • Full, empty and nominal, and the resistance inside a cell.
  • 2S adds voltages, and the weakest cell sets the end.
  • A bleed resistor and a MOSFET per cell.
  • Volts against counted coulombs, and a capacity that fades.
  • Overcurrent, undervoltage and imbalance, latched until reset.
  • Constant current, constant voltage and the end of charge.
  • A 2S monitor with your own limits.

Materials for the whole unit

  • Arduino Uno R3
  • Battery: AA, coin cell, LiPo x 2
  • Bench power supply
  • Current monitor, INA219
  • Li-ion charger, TP4056
  • MOSFET x 2
  • Multimeter x 3
  • Resistor x 5
  • Slide switch x 2

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 1 h

Chemistries

Full, empty and nominal, and the resistance inside a cell.

LessonTimeWhat students do
Chemistries: what a cell's voltage tells youOne 18650 on a meter and a 4 ohm load: 4.2 V full, 3.0 V empty, the sag under load from internal resistance, a small pouch that sags more, and how lithium-ion, LiFePO4, NiMH and lead-acid compare.60 min
  1. Run it: a full cell
  2. Under load
  3. Half full
  4. Empty
  5. A small pouch sags more
  6. Predict: four NiMH cells

Materials

  • Battery: AA, coin cell, LiPo
  • Multimeter
  • Resistor
  • Slide switch

Check for understanding

Each student finishes "Chemistries: what a cell's voltage tells you" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Predict: four NiMH cells".

Chapter 2. About 50 min

Series strings

2S adds voltages, and the weakest cell sets the end.

LessonTimeWhat students do
Series strings: 2S and the weakest cellTwo 18650s in series make 8.4 V: the same current through both, a mismatched cell, and a weak cell that hits empty while the pack voltage still looks healthy, which is why a BMS measures every cell.50 min
  1. Run it: 8.4 V
  2. One current through both
  3. A mismatched cell
  4. The weak cell hits bottom
  5. Predict: two cells at 90 percent

Materials

  • Battery: AA, coin cell, LiPo x 2
  • Multimeter x 3
  • Resistor
  • Slide switch

Check for understanding

Each student finishes "Series strings: 2S and the weakest cell" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Predict: two cells at 90 percent".

Chapter 3. About 50 min

Balancing

A bleed resistor and a MOSFET per cell.

LessonTimeWhat students do
Balancing: bleeding the high cellA 2S pack 0.24 V out of balance: a bleed resistor and an AO3400A drain the high cell alone, watch it come down to its neighbor, work out the heat, and balance the bottom cell too.50 min
  1. Run it: out of balance
  2. Bleed cell A
  3. Watch it come down
  4. Predict: a gentler bleed
  5. The bottom cell

Materials

  • Battery: AA, coin cell, LiPo x 2
  • MOSFET x 2
  • Multimeter x 2
  • Resistor x 4
  • Slide switch x 2

Check for understanding

Each student finishes "Balancing: bleeding the high cell" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "The bottom cell".

Chapter 4. About 40 min

State of charge

Volts against counted coulombs, and a capacity that fades.

LessonTimeWhat students do
State of charge: volts and coulombsAn Uno watches a 2S pack with a cell tap, a divider and an INA219: state of charge from the lowest cell's voltage, and by counting the charge that flows out, which agree until the capacity is wrong.40 min
  1. Run it: watching every cell
  2. Count the coulombs
  3. When the capacity is wrong
  4. Predict: at rest

Materials

  • Arduino Uno R3
  • Battery: AA, coin cell, LiPo x 2
  • Current monitor, INA219
  • MOSFET
  • Resistor x 5
  • Slide switch

Check for understanding

Each student finishes "State of charge: volts and coulombs" on their own, without opening the hints. The simulator checks 4 of its 4 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Predict: at rest".

Chapter 5. About 50 min

Protection

Overcurrent, undervoltage and imbalance, latched until reset.

LessonTimeWhat students do
Protection: the MOSFET that says noThe pack monitor opens its low-side MOSFET on overcurrent, latches until reset, cuts off a weak cell at 3.0 V, takes a higher undervoltage setting, and warns of imbalance.50 min
  1. Overcurrent
  2. A trip latches
  3. Undervoltage
  4. Your setting: a safer cutoff
  5. Imbalance

Materials

  • Arduino Uno R3
  • Battery: AA, coin cell, LiPo x 2
  • Current monitor, INA219
  • MOSFET
  • Resistor x 5
  • Slide switch

Check for understanding

Each student finishes "Protection: the MOSFET that says no" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Imbalance".

Chapter 6. About 50 min

Charging profiles

Constant current, constant voltage and the end of charge.

LessonTimeWhat students do
Charging profiles: CC, then CV, then stopA TP4056 charges one 18650: a constant 1 A, the cell voltage climbing, the switch to constant 4.2 V as the current tapers, and the standby lamp at the end, with the rules for charging lithium safely.50 min
  1. Run it: constant current
  2. The cell climbs
  3. Constant voltage: the taper
  4. Done
  5. Two cells need a balance charger

Materials

  • Battery: AA, coin cell, LiPo
  • Bench power supply
  • Li-ion charger, TP4056
  • Multimeter

Check for understanding

Each student finishes "Charging profiles: CC, then CV, then stop" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Two cells need a balance charger".

Chapter 7. About 1 h

Boss build

A 2S monitor with your own limits.

LessonTimeWhat students do
Boss: a 2S pack monitorWire the protection MOSFET, then run a 2S monitor that watches each cell, counts the charge out, trips on overcurrent and undervoltage, and takes the limits you set for your own pack.60 min
  1. Wire the protection MOSFET
  2. Run it: output on
  3. Prove the overcurrent trip
  4. Your pack, your limit
  5. Your cutoff
  6. Count your pack

Materials

  • Arduino Uno R3
  • Battery: AA, coin cell, LiPo x 2
  • Current monitor, INA219
  • MOSFET
  • Resistor x 5
  • Slide switch

Check for understanding

Each student finishes "Boss: a 2S pack monitor" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Count your pack".

Your class

Teach this unit as a class

Start a class from this course and its 7 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.