All paths

Audio electronics

Advanced, after the Op-amp circuit cookbook: preamps, tone controls, amplifier classes, distortion, speakers and impedance, hum and noise, and a class A guitar amp channel you voice yourself.

Free7 lessons6 h7 chapters1,856 XPElectrical · Advanced+250 XP

0 of 7 done

What you will build

0 projects, built step by step

7 lessons in 7 chapters, about 6 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

Preamps

Gain, input impedance, headroom and a log volume pot.

  1. Open288 XP

    Preamps

    A guitar into a TL072 preamp: gain in decibels, the input impedance a pickup needs, the headroom a hot pickup eats, and why a volume knob is a log pot.

    0 of 6 steps

4 questions, graded as you go.
Chapter 2

Tone controls

A treble cut and a bass cut, each one RC corner.

  1. Locked250 XP

    Tone controls

    A guitar's own treble-cut knob and a bass-cut coupling capacitor, each buffered by half a TL072: a 723 Hz corner that darkens the highs and leaves the lows alone, and a 159 Hz corner that thins the bass.

    0 of 5 steps

3 questions, graded as you go.
Chapter 3

Amplifier classes

Where the watts go in class AB and class A.

  1. Locked250 XP

    Amplifier classes

    Where a power amp's watts go: a class AB push-pull stage that idles at 190 mA and reaches 31 percent at full drive, and a class A stage that burns 22 W to deliver 2. The efficiency arithmetic behind class D.

    0 of 5 steps

4 questions, graded as you go.
Chapter 4

Distortion

Soft clipping, hard clipping and asymmetry.

  1. Locked288 XP

    Distortion

    A TL072 gain stage into back-to-back diodes: a clipper that leaves a small signal alone and squashes a big one, a drive knob that changes the sound more than the level, asymmetric clipping that adds DC, and the hard clip of the rails.

    0 of 6 steps

3 questions, graded as you go.
Chapter 5

Speakers and impedance

Watts into ohms, cables and damping factor.

  1. Locked288 XP

    Speakers and impedance

    An amp into an 8 ohm speaker: P = V squared over R, a 4 ohm load that doubles the watts, a thin cable that steals them, a tube amp's output impedance and damping factor, and why half the volts is a quarter of the power.

    0 of 6 steps

3 questions, graded as you go.
Chapter 6

Hum and noise

Ground loops, balanced inputs and grounding rules.

  1. Locked265 XP

    Hum and noise

    A ground loop puts 60 Hz under the guitar: a single-ended input amplifies it, a balanced input throws it away, a high pass only half helps, and a 120 Hz buzz gets through more. The grounding rules that prevent it.

    0 of 6 steps

3 questions, graded as you go.
Chapter 7

Boss build

A class A guitar amp channel, voiced by you.

  1. Locked227 XP

    Boss build: a class A guitar amp channel

    A whole channel: a TL072 preamp with a gain knob, diode overdrive, a tone knob, a power stage and a class A TIP41C into an 8 ohm load. Set it clean, then dirty, read what the output stage burns, and voice it yourself.

    0 of 5 steps

3 questions, graded as you go.
Syllabus

Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

Preamps

  1. PreampsA guitar into a TL072 preamp: gain in decibels, the input impedance a pickup needs, the headroom a hot pickup eats, and why a volume knob is a log pot.
Chapter 2

Tone controls

  1. Tone controlsA guitar's own treble-cut knob and a bass-cut coupling capacitor, each buffered by half a TL072: a 723 Hz corner that darkens the highs and leaves the lows alone, and a 159 Hz corner that thins the bass.
Chapter 3

Amplifier classes

  1. Amplifier classesWhere a power amp's watts go: a class AB push-pull stage that idles at 190 mA and reaches 31 percent at full drive, and a class A stage that burns 22 W to deliver 2. The efficiency arithmetic behind class D.
Chapter 4

Distortion

  1. DistortionA TL072 gain stage into back-to-back diodes: a clipper that leaves a small signal alone and squashes a big one, a drive knob that changes the sound more than the level, asymmetric clipping that adds DC, and the hard clip of the rails.
Chapter 5

Speakers and impedance

  1. Speakers and impedanceAn amp into an 8 ohm speaker: P = V squared over R, a 4 ohm load that doubles the watts, a thin cable that steals them, a tube amp's output impedance and damping factor, and why half the volts is a quarter of the power.
Chapter 6

Hum and noise

  1. Hum and noiseA ground loop puts 60 Hz under the guitar: a single-ended input amplifies it, a balanced input throws it away, a high pass only half helps, and a 120 Hz buzz gets through more. The grounding rules that prevent it.
Chapter 7

Boss build

  1. Boss build: a class A guitar amp channelA whole channel: a TL072 preamp with a gain knob, diode overdrive, a tone knob, a power stage and a class A TIP41C into an 8 ohm load. Set it clean, then dirty, read what the output stage burns, and voice it yourself.
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Audio electronics

Is Audio electronics free?

Yes. All 7 lessons of Audio electronics are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does Audio electronics take?

About 6 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Preamps", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.