Lesson plan

Audio electronics lesson plan

Advanced, after the Op-amp circuit cookbook: preamps, tone controls, amplifier classes, distortion, speakers and impedance, hum and noise, and a class A guitar amp channel you voice yourself.

7 chapters, 7 lessons, about 6 hours, no board. Every lesson runs in the browser, with nothing to install.

The unit

Objectives and materials

By the end, students can

  • Gain, input impedance, headroom and a log volume pot.
  • A treble cut and a bass cut, each one RC corner.
  • Where the watts go in class AB and class A.
  • Soft clipping, hard clipping and asymmetry.
  • Watts into ohms, cables and damping factor.
  • Ground loops, balanced inputs and grounding rules.
  • A class A guitar amp channel, voiced by you.

Materials for the whole unit

  • Capacitor x 2
  • Diode x 2
  • Function generator x 2
  • Multimeter x 5
  • Oscilloscope
  • Potentiometer
  • Resistor x 11
  • Signal generator
  • Slide switch
  • Speaker, 8 ohm x 2
  • TL072 dual JFET op-amp
  • Transistor (NPN or PNP) x 3

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 55 min

Preamps

Gain, input impedance, headroom and a log volume pot.

LessonTimeWhat students do
PreampsA guitar into a TL072 preamp: gain in decibels, the input impedance a pickup needs, the headroom a hot pickup eats, and why a volume knob is a log pot.55 min
  1. Run it: a gain of 11
  2. Gain in decibels
  3. Input impedance
  4. Headroom
  5. The volume knob
  6. Why the taper is log

Materials

  • Function generator
  • Multimeter x 3
  • Oscilloscope
  • Potentiometer
  • Resistor x 5
  • TL072 dual JFET op-amp

Check for understanding

Each student finishes "Preamps" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Why the taper is log".

Chapter 2. About 45 min

Tone controls

A treble cut and a bass cut, each one RC corner.

LessonTimeWhat students do
Tone controlsA guitar's own treble-cut knob and a bass-cut coupling capacitor, each buffered by half a TL072: a 723 Hz corner that darkens the highs and leaves the lows alone, and a 159 Hz corner that thins the bass.45 min
  1. Run it: knob on 10
  2. Knob on 0
  3. The lows walk through
  4. Bass cut
  5. Predict: a fatter capacitor

Materials

  • Capacitor x 2
  • Function generator
  • Multimeter x 3
  • Resistor x 3
  • TL072 dual JFET op-amp

Check for understanding

Each student finishes "Tone controls" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Predict: a fatter capacitor".

Chapter 3. About 45 min

Amplifier classes

Where the watts go in class AB and class A.

LessonTimeWhat students do
Amplifier classesWhere a power amp's watts go: a class AB push-pull stage that idles at 190 mA and reaches 31 percent at full drive, and a class A stage that burns 22 W to deliver 2. The efficiency arithmetic behind class D.45 min
  1. Run it: class AB
  2. What the supply gives
  3. Turn it up
  4. Class A idles hot
  5. Class A at full drive

Materials

  • Diode x 2
  • Function generator x 2
  • Multimeter x 5
  • Oscilloscope
  • Resistor x 5
  • Speaker, 8 ohm x 2
  • Transistor (NPN or PNP) x 3

Check for understanding

Each student finishes "Amplifier classes" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Class A at full drive".

Chapter 4. About 55 min

Distortion

Soft clipping, hard clipping and asymmetry.

LessonTimeWhat students do
DistortionA TL072 gain stage into back-to-back diodes: a clipper that leaves a small signal alone and squashes a big one, a drive knob that changes the sound more than the level, asymmetric clipping that adds DC, and the hard clip of the rails.55 min
  1. Run it: gain before the clipper
  2. The diodes squash it
  3. Drive down: clean
  4. Drive up: compression
  5. Asymmetric clipping
  6. Hard clipping at the rails

Materials

  • Diode x 2
  • Function generator
  • Multimeter x 3
  • Oscilloscope
  • Resistor x 5
  • TL072 dual JFET op-amp

Check for understanding

Each student finishes "Distortion" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Hard clipping at the rails".

Chapter 5. About 55 min

Speakers and impedance

Watts into ohms, cables and damping factor.

LessonTimeWhat students do
Speakers and impedanceAn amp into an 8 ohm speaker: P = V squared over R, a 4 ohm load that doubles the watts, a thin cable that steals them, a tube amp's output impedance and damping factor, and why half the volts is a quarter of the power.55 min
  1. Run it: 2 W into 8 ohms
  2. A 4 ohm speaker
  3. The cable steals watts
  4. A tube amp's output
  5. Two cabinets
  6. Predict: half the volts

Materials

  • Multimeter x 2
  • Resistor x 3
  • Signal generator
  • Slide switch
  • Speaker, 8 ohm x 2

Check for understanding

Each student finishes "Speakers and impedance" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Predict: half the volts".

Chapter 6. About 55 min

Hum and noise

Ground loops, balanced inputs and grounding rules.

LessonTimeWhat students do
Hum and noiseA ground loop puts 60 Hz under the guitar: a single-ended input amplifies it, a balanced input throws it away, a high pass only half helps, and a 120 Hz buzz gets through more. The grounding rules that prevent it.55 min
  1. Run it: guitar plus hum
  2. Mute the guitar
  3. A balanced input
  4. Filter it out?
  5. The buzz is worse
  6. Grounding rules

Materials

  • Capacitor
  • Function generator
  • Multimeter x 3
  • Resistor x 7
  • Signal generator
  • TL072 dual JFET op-amp

Check for understanding

Each student finishes "Hum and noise" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Grounding rules".

Chapter 7. About 45 min

Boss build

A class A guitar amp channel, voiced by you.

LessonTimeWhat students do
Boss build: a class A guitar amp channelA whole channel: a TL072 preamp with a gain knob, diode overdrive, a tone knob, a power stage and a class A TIP41C into an 8 ohm load. Set it clean, then dirty, read what the output stage burns, and voice it yourself.45 min
  1. Run it: clean
  2. Turn the gain up
  3. What class A costs
  4. Make it yours: voice the clean channel
  5. Your amp sheet

Materials

  • Capacitor x 2
  • Diode x 2
  • Function generator
  • Multimeter x 3
  • Oscilloscope
  • Resistor x 11
  • TL072 dual JFET op-amp
  • Transistor (NPN or PNP)

Check for understanding

Each student finishes "Boss build: a class A guitar amp channel" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Your amp sheet".

Your class

Teach this unit as a class

Start a class from this course and its 7 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.