All paths

Low-voltage alarm circuits

How a burglar alarm thinks: NC loops, end-of-line and supervised zones, sirens and strobes, keypads and arming, battery backup, and a four-zone panel you wire and make your own.

Free7 lessons6 h7 chapters1,727 XPElectrical · Intermediate+150 XP

0 of 7 done

Start the course freeNormally closed loops: why alarms are wired backwardsLesson plan for teachers
What you will build

0 projects, built step by step

7 lessons in 7 chapters, about 6 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

Normally closed loops

Contacts in series that fail safe, and an NO button that fails silently.

  1. Open249 XP

    Normally closed loops: why alarms are wired backwards

    Three door contacts in series hold a MOSFET off: open any door and the alarm lamp lights, cut the wire and it lights too. The same test on a normally open panic button shows why alarms fail safe.

    0 of 7 steps

4 questions, graded as you go.
Chapter 2

End-of-line resistors

A resistor at the far end lets the panel see a jumper.

  1. Locked236 XP

    End-of-line resistors: seeing the wire itself

    A 4.7k resistor at the far end of the loop gives the panel a middle voltage to expect: a door reads high, a burglar's jumper reads low, and a plain loop cannot tell the jumper from a shut door.

    0 of 6 steps

4 questions, graded as you go.
Chapter 3

Supervised zones

Double end-of-line: normal, open, cut and short on two wires.

  1. Locked205 XP

    Supervised zones: four states on two wires

    Double end-of-line wiring: a resistor in series and another across the contact give a panel four voltages, so it tells a shut door, an open door, a cut wire and a short apart.

    0 of 5 steps

4 questions, graded as you go.
Chapter 4

Sirens and strobes

A MOSFET bell output, its current, and the run that silences a siren.

  1. Locked236 XP

    Sirens and strobes: the bell output

    A MOSFET switches a 12 V siren and a strobe at the end of a wire run: their current, why a long thin run can silence a siren, and adding a second siren to the bell output.

    0 of 6 steps

4 questions, graded as you go.
Chapter 5

Keypads and arming

An Uno panel: away, stay, exit and entry delays, and not-ready zones.

  1. Locked267 XP

    Keypads and arming: an Uno becomes a panel

    An Uno reads three DEOL zones on its analog pins, a PIR and a 4x4 keypad: arm away, the exit delay, not-ready zones, the entry delay, an alarm with siren and strobe, and arming stay.

    0 of 7 steps

4 questions, graded as you go.
Chapter 6

Battery backup

A float charger and a lead-acid battery that take over without a gap.

  1. Locked236 XP

    Battery backup: an alarm that works in a power cut

    A 13.8 V charger, a 12 V 7 Ah lead-acid battery and a panel on one bus: watch the battery current change sign when the power fails, carry the siren, and drain, and work out standby time.

    0 of 6 steps

4 questions, graded as you go.
Chapter 7

Boss build

Wire a zone, walk test, change the code, bypass, catch a tamper, set the bell cutoff.

  1. Locked298 XP

    Boss: a four-zone panel

    Wire the window's DEOL loop, walk test every zone, change the master code, bypass a zone, catch a tamper and set your own bell cutoff: a four-zone panel with keypad, siren and strobe, made yours.

    0 of 8 steps

4 questions, graded as you go.
Syllabus

Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

Normally closed loops

  1. Normally closed loops: why alarms are wired backwardsThree door contacts in series hold a MOSFET off: open any door and the alarm lamp lights, cut the wire and it lights too. The same test on a normally open panic button shows why alarms fail safe.
Chapter 2

End-of-line resistors

  1. End-of-line resistors: seeing the wire itselfA 4.7k resistor at the far end of the loop gives the panel a middle voltage to expect: a door reads high, a burglar's jumper reads low, and a plain loop cannot tell the jumper from a shut door.
Chapter 3

Supervised zones

  1. Supervised zones: four states on two wiresDouble end-of-line wiring: a resistor in series and another across the contact give a panel four voltages, so it tells a shut door, an open door, a cut wire and a short apart.
Chapter 4

Sirens and strobes

  1. Sirens and strobes: the bell outputA MOSFET switches a 12 V siren and a strobe at the end of a wire run: their current, why a long thin run can silence a siren, and adding a second siren to the bell output.
Chapter 5

Keypads and arming

  1. Keypads and arming: an Uno becomes a panelAn Uno reads three DEOL zones on its analog pins, a PIR and a 4x4 keypad: arm away, the exit delay, not-ready zones, the entry delay, an alarm with siren and strobe, and arming stay.
Chapter 6

Battery backup

  1. Battery backup: an alarm that works in a power cutA 13.8 V charger, a 12 V 7 Ah lead-acid battery and a panel on one bus: watch the battery current change sign when the power fails, carry the siren, and drain, and work out standby time.
Chapter 7

Boss build

  1. Boss: a four-zone panelWire the window's DEOL loop, walk test every zone, change the master code, bypass a zone, catch a tamper and set your own bell cutoff: a four-zone panel with keypad, siren and strobe, made yours.
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Low-voltage alarm circuits

Is Low-voltage alarm circuits free?

Yes. All 7 lessons of Low-voltage alarm circuits are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does Low-voltage alarm circuits take?

About 6 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Normally closed loops: why alarms are wired backwards", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.