Lesson plan

Low-voltage alarm circuits lesson plan

How a burglar alarm thinks: NC loops, end-of-line and supervised zones, sirens and strobes, keypads and arming, battery backup, and a four-zone panel you wire and make your own.

7 chapters, 7 lessons, about 6 hours, no board. Every lesson runs in the browser, with nothing to install.

The unit

Objectives and materials

By the end, students can

  • Contacts in series that fail safe, and an NO button that fails silently.
  • A resistor at the far end lets the panel see a jumper.
  • Double end-of-line: normal, open, cut and short on two wires.
  • A MOSFET bell output, its current, and the run that silences a siren.
  • An Uno panel: away, stay, exit and entry delays, and not-ready zones.
  • A float charger and a lead-acid battery that take over without a gap.
  • Wire a zone, walk test, change the code, bypass, catch a tamper, set the bell cutoff.

Materials for the whole unit

  • Alarm siren, 12 V x 2
  • Arduino Uno R3
  • Battery: AA, coin cell, LiPo
  • Bench power supply x 2
  • Buzzer
  • D4184 dual MOSFET switch module x 2
  • DC jack and adapter
  • Filament lamp x 2
  • Keypad, 4x4
  • MOSFET x 2
  • Motion sensor
  • Multimeter
  • Pushbutton
  • Reed switch x 3
  • Resistor x 9
  • Slide switch x 2

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 55 min

Normally closed loops

Contacts in series that fail safe, and an NO button that fails silently.

LessonTimeWhat students do
Normally closed loops: why alarms are wired backwardsThree door contacts in series hold a MOSFET off: open any door and the alarm lamp lights, cut the wire and it lights too. The same test on a normally open panic button shows why alarms fail safe.55 min
  1. Run it: every door is open
  2. Shut the doors
  3. Open one door
  4. Cut the wire
  5. A normally open panic button
  6. Cut the NO wire
  7. Predict: standby current

Materials

  • Bench power supply
  • Filament lamp x 2
  • MOSFET x 2
  • Multimeter
  • Pushbutton
  • Reed switch x 3
  • Resistor x 3
  • Slide switch x 2

Check for understanding

Each student finishes "Normally closed loops: why alarms are wired backwards" on their own, without opening the hints. The simulator checks 7 of its 7 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Predict: standby current".

Chapter 2. About 50 min

End-of-line resistors

A resistor at the far end lets the panel see a jumper.

LessonTimeWhat students do
End-of-line resistors: seeing the wire itselfA 4.7k resistor at the far end of the loop gives the panel a middle voltage to expect: a door reads high, a burglar's jumper reads low, and a plain loop cannot tell the jumper from a shut door.50 min
  1. Shut the doors: half of 5 V
  2. Open a door
  3. The jumper
  4. Without the EOL
  5. Predict: a 2.2k EOL
  6. The wrong resistor

Materials

  • Bench power supply
  • Multimeter
  • Reed switch x 2
  • Resistor x 2
  • Slide switch

Check for understanding

Each student finishes "End-of-line resistors: seeing the wire itself" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "The wrong resistor".

Chapter 3. About 40 min

Supervised zones

Double end-of-line: normal, open, cut and short on two wires.

LessonTimeWhat students do
Supervised zones: four states on two wiresDouble end-of-line wiring: a resistor in series and another across the contact give a panel four voltages, so it tells a shut door, an open door, a cut wire and a short apart.40 min
  1. Run it: the door is open, 3.33 V
  2. Shut the door: 2.50 V
  3. Cut the wire: 5 V
  4. Short the wires: 0 V
  5. Predict: 2.2k resistors

Materials

  • Bench power supply
  • Multimeter
  • Reed switch
  • Resistor x 3
  • Slide switch x 2

Check for understanding

Each student finishes "Supervised zones: four states on two wires" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Predict: 2.2k resistors".

Chapter 4. About 50 min

Sirens and strobes

A MOSFET bell output, its current, and the run that silences a siren.

LessonTimeWhat students do
Sirens and strobes: the bell outputA MOSFET switches a 12 V siren and a strobe at the end of a wire run: their current, why a long thin run can silence a siren, and adding a second siren to the bell output.50 min
  1. Sound it
  2. The strobe
  3. How much current
  4. Predict: a long thin run
  5. Too far, too thin
  6. A second siren

Materials

  • Alarm siren, 12 V x 2
  • Bench power supply x 2
  • Filament lamp
  • MOSFET
  • Multimeter
  • Resistor x 4
  • Slide switch

Check for understanding

Each student finishes "Sirens and strobes: the bell output" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A second siren".

Chapter 5. About 55 min

Keypads and arming

An Uno panel: away, stay, exit and entry delays, and not-ready zones.

LessonTimeWhat students do
Keypads and arming: an Uno becomes a panelAn Uno reads three DEOL zones on its analog pins, a PIR and a 4x4 keypad: arm away, the exit delay, not-ready zones, the entry delay, an alarm with siren and strobe, and arming stay.55 min
  1. Run it and shut up the house
  2. Press a key
  3. Arm away
  4. Not ready
  5. Come home: the entry delay
  6. Let it run out
  7. Arm stay

Materials

  • Alarm siren, 12 V
  • Arduino Uno R3
  • Buzzer
  • D4184 dual MOSFET switch module x 2
  • DC jack and adapter
  • Filament lamp
  • Keypad, 4x4
  • Motion sensor
  • Reed switch x 3
  • Resistor x 9
  • Slide switch

Check for understanding

Each student finishes "Keypads and arming: an Uno becomes a panel" on their own, without opening the hints. The simulator checks 7 of its 7 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Arm stay".

Chapter 6. About 50 min

Battery backup

A float charger and a lead-acid battery that take over without a gap.

LessonTimeWhat students do
Battery backup: an alarm that works in a power cutA 13.8 V charger, a 12 V 7 Ah lead-acid battery and a panel on one bus: watch the battery current change sign when the power fails, carry the siren, and drain, and work out standby time.50 min
  1. Run it: on mains
  2. Where the current goes
  3. Pull the plug
  4. The alarm, on battery
  5. Watch it drain
  6. Predict: half the standby load

Materials

  • Alarm siren, 12 V
  • Battery: AA, coin cell, LiPo
  • Bench power supply
  • Multimeter
  • Resistor x 3
  • Slide switch

Check for understanding

Each student finishes "Battery backup: an alarm that works in a power cut" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Predict: half the standby load".

Chapter 7. About 1 h 5 min

Boss build

Wire a zone, walk test, change the code, bypass, catch a tamper, set the bell cutoff.

LessonTimeWhat students do
Boss: a four-zone panelWire the window's DEOL loop, walk test every zone, change the master code, bypass a zone, catch a tamper and set your own bell cutoff: a four-zone panel with keypad, siren and strobe, made yours.65 min
  1. Wire the window
  2. Run it: all four zones ready
  3. Walk test
  4. Your own code
  5. Bypass a zone
  6. Catch a tamper
  7. Your change: the bell cutoff
  8. Last run: motion

Materials

  • Alarm siren, 12 V
  • Arduino Uno R3
  • Buzzer
  • D4184 dual MOSFET switch module x 2
  • DC jack and adapter
  • Filament lamp
  • Keypad, 4x4
  • Motion sensor
  • Reed switch x 3
  • Resistor x 9
  • Slide switch

Check for understanding

Each student finishes "Boss: a four-zone panel" on their own, without opening the hints. The simulator checks 8 of its 8 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Last run: motion".

Your class

Teach this unit as a class

Start a class from this course and its 7 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.