gEDA schematic viewer online: open a gschem or Lepton EDA .sch
Open a gschem .sch file online, or one from Lepton EDA, which carries gEDA on and writes the same format.
Drop it here, or paste it
Drop it here and Mokxi places the stock resistors, capacitors, diodes, LEDs, transistors, sources and power symbols where the schematic has them, joins the N segments into nets, and runs the result in your browser. No gschem, no symbol library, nothing to install.
The two-stage amplifier from the gEDA examples: a 15 V VCC source, a 1 mV 1 kHz input, bias and load resistors, coupling capacitors, and SPICE model, include and directive symbols. Twenty-seven parts open joined; the two transistors use transistor.sym, a symbol with no pins on file, so they are notes to swap for Mokxi NPNs.
Paste from ChatGPT or ClaudeCopy a prompt, say what to build, paste the answer.
- 1Copy the promptIt teaches your AI how to write a Mokxi project.
- 2Say what to buildPaste the prompt into ChatGPT, Claude, Gemini or Cursor and add what you want, like "a night light with a light sensor".
- 3Paste its answer hereThe whole reply is fine. It opens wired and ready to run.
Only have a photo or a screenshot of the circuit? Give your AI the picture with this prompt instead.
Your AI app supports MCP? Add the Mokxi server and it builds the link for you. How
From Tinkercad? Three stepsBring a circuit across wired, with its code.
- 1Export the circuitIn Tinkercad, open the circuit, press Export and download the .brd file. It has every part and wire.
- 2Download the codeOpen Code, switch to Text and press the download button for the .ino.
- 3Drop both hereChoose or drop the .brd and the .ino together: it opens wired, with the code on the board. No .brd? Paste the Component List with the code under it.
What Mokxi reads from gEDA
A .sch whose first line is v YYYYMMDD 1 or v YYYYMMDD 2 (the version that wrote it, then the file format) and which has a C or N object. gschem and Lepton EDA both write this.
Schematics from before 2003 as well: a reference written as uref is read as refdes.
The schematic text, pasted rather than dropped.
Embedded symbols (C ... EMBEDDEDname.sym, with the symbol's objects between [ and ]), which carry their own pins and are read even when they are not stock symbols.
What comes across
The stock symbols
resistor-1 and -2, capacitor-1, -2 and -3, inductor-1, diode-1, zener-1, led-1, -2 and -3, npn-1, -2 and -3, pnp-1, -2 and -3, nmos-1 and -3, pmos-1 and -3, battery-1 and -2, resistor-variable-1 and -2 (a pot, pin 3 the wiper), vdc-1, voltage-3, vsin-1, switch-pushbutton-no-1, opamp-1 and gnd-1. Each pin's connectable end was copied from the symbol file in Lepton's library, so a symbol placed mirrored and turned still meets its nets.
Nets, the gschem way
A segment end that meets another segment's end, lands on the middle of one, or touches a pin's connectable end is joined; segments with the same netname attribute are one net. Coordinates are read as mils with y up, as the file has them.
Power symbols as nets, and a supply when none is drawn
vcc-1, vdd-1, vee-1, generic-power, 5V-plus-1, 3.3V-plus-1 and 12V-plus-1 are named nets, not parts, joined through their net= attribute. When a supply net has no source on it, Mokxi puts a supply where its first symbol stood: +5V, +3.3V and +12V at the voltage in their name, Vcc or Vdd at 5 V with a note to set it. A gnd-1 is a Mokxi ground.
Values and models
value=28K is 28 kΩ and value=2.2uF is 2.2 µF; a vdc-1 with DC 15V is a 15 V source, and a vsin-1 with SIN(0 1MV 1KHZ) is a 1 mV, 1 kHz generator. A model-name on a diode or transistor (2N3904) is kept when Mokxi has it; otherwise Mokxi's usual part of that type is used.
Embedded symbols
A symbol embedded in the schematic brings its pins already placed, so a part that is none of the stock symbols is still read when its refdes, device and value say what it is, its pins matched by their own labels and numbers. A slotted symbol (one gate of a 7400) and a diode whose pins are not named anode and cathode stay notes.
What does not, and what happens instead
Title blocks, SPICE blocks and port flags
title-*.sym, spice-directive, spice-model, spice-include and spice-subcircuit symbols, and the in, out and io port flags are not parts. One report line says they were left out.
Buses
A U bus object is left out, with the note to draw its signals as wires.
Symbols whose pins are not in the file
gEDA keeps a symbol's pins in its .sym, which the schematic does not carry, so any non-embedded symbol outside the stock list (a 7400, a connector, a custom transistor.sym) becomes a note naming its device and refdes, and the report explains why.
MOSFET bulk pins
nmos-1 and pmos-1 have four pins. The bulk is left out quietly and mentioned once: Mokxi's MOSFETs have three.
From gEDA to Mokxi
Step 1
In gschem or Lepton EDA's schematic editor, save the schematic as a .sch.
Step 2
Drop the schematic onto the box above or the editor, or paste what is in it; Mokxi recognizes the version line and an object and shows "Looks like a gEDA schematic".
Step 3
The circuit opens with its parts in place, and the summary chip lists any supply Mokxi added, the SPICE blocks it dropped, and each symbol that became a note.
Step 4
Press Run and probe the nets by name; T tidies the wires.
Questions about importing from gEDA
Can I view a gschem .sch without installing gEDA?
Yes. Drop the .sch here and it opens as a circuit in the editor, with the stock symbols placed and the nets joined. It is a working circuit you can run, so a probe on a net shows its voltage.
Does it read Lepton EDA files?
Yes. Lepton EDA carries gEDA on and writes the same .sch format, and the pins in Mokxi's table were copied from Lepton's own symbol library. A file from either tool is read the same way.
Why are some of my symbols notes?
A gEDA schematic holds only a symbol's name and position; the pins are in the .sym file, which is not in the schematic. Mokxi knows the pins of the stock symbols listed above and of any symbol embedded in the file, and shows every other one as a note with its device and refdes.
Where does the 5 V supply come from?
A Vcc or Vdd power symbol names a net but does not power it. If nothing on that net is a source, Mokxi adds a 5 V supply so the circuit runs and says so in the report; set the voltage in the supply's settings. A +12V or +3.3V symbol gets the voltage its name says.
What happens to my SPICE directives and models?
spice-directive, spice-model and spice-include symbols are not parts, so they are left out with one line in the report. Mokxi uses its own models for the parts it places, and a model-name attribute is kept only when Mokxi has that exact part.
Is a KiCad .sch the same thing?
No. KiCad's legacy schematics share the extension but not the format, and Mokxi tells the two apart by the first line. A KiCad .sch goes to the KiCad importer; a Qucs .sch to the Qucs one.
Where to next
What this page says about gEDA was checked in November 2026 against gEDA project, Lepton EDA.
