Bài học và trò chơi học tập

Xây pedal hiệu ứng số

Một pedal hiệu ứng guitar trên Uno, kèm máy phát sóng thay cho guitar.

Pédal hoàn chỉnh

Xây pedal hiệu ứng kỹ thuật số dùng chung một bo mạch cho mọi bài học:

  • The guitar: a máy tạo tín hiệu, sóng sin 220 Hz, đỉnh 2 V, lấy 0 V làm tâm như tín hiệu của pickup.
  • The input: a 1 uF capacitor into A0, held at 2.5 V by two 10 k resistors: đó là điện áp phân cực.
  • The brain: an Arduino Uno, ADC của nó chạy liên tục trên A0 và Timer 2 ngắt 15.625 lần mỗi giây.
  • Đầu ra: PWM 8-bit ở 62.5 kHz trên chân 9, được làm mượt bằng 1 k và 100 nF, rồi qua 1 uF tới một piezo phát ra cao độ mà nó nghe được.
  • Controls: a potentiometer on A1, and two công tắc chân: MUTE on pin 2 stops the strings, FX on pin 3 switches the effect.

Đây là pedal guitar kỹ thuật số. Nó khác với pedal trong mô phỏng đua xe ở bài Xây pedal cảm biến lực.

Cách hoạt động

In and out. The capacitor blocks DC and the divider puts the swing in the middle of the ADC's 0 to 5 V; the code subtracts 128 to take the bias off. Each interrupt takes the latest sample, runs the effect and writes OCR1A. The knob is read eight times a second by borrowing the ADC for a sample.

Gain and clipping. Multiply, then limit: hard clipping cuts flat at the rails; soft clipping bends through y = 1.5t - 0.5t^3 first, from a 256-entry table.

Delay. A ring buffer of 1,280 bytes, all the Uno's 2 KB can spare beside the stack: 81 ms at most. Feedback writes some of the echo back for repeats, and MUTE measures the tail.

Tremolo. A slow phase accumulator, an LFO, scales every sample between 1 - depth and 1, as a triangle or a square.

Wah. Chamberlin's state-variable filter in fixed point, its band-pass output swept from 200 Hz to 2 kHz by the knob or by an LFO for auto-wah.

Latency. Sample by sample, the output follows the input within a tick. Working in blocks of 64 or 256 adds 4.1 or 16.4 ms, measured with MUTE.

Khóa học

  1. Âm thanh vào và ra: điện áp phân cực, biên độ, lấy mẫu và Nyquist, và vì sao đầu vào thật cần một bộ đệm.
  2. Gain and clipping: clean gain, hard and soft clipping, and harmonics.
  3. Delay: a ring buffer, feedback, the tail, and the 2 KB limit.
  4. Tremolo: tốc độ, độ sâu và dạng sóng của LFO.
  5. Wah: band-pass quét được, auto-wah và Q.
  6. Độ trễ: xử lý từng mẫu so với xử lý theo khối.
  7. Dự án: pedals hai hiệu ứng: drive và tremolo nối tiếp, bypass, và đổi thứ tự.

Mỗi bước được kiểm tra đều được đối chiếu với mạch đang chạy.