Lesson plan

DC motors and generators lesson plan

The brushed DC machine as a component: torque from current, back EMF, the torque-speed line, generator mode, where the watts go, three ways to brake, and an Uno motor dyno you build yourself.

7 chapters, 7 lessons, about 5 hours, no board. Every lesson runs in the browser, with nothing to install.

The unit

Objectives and materials

By the end, students can

  • Torque is current, from stall to free running.
  • A spinning motor pushes back, in proportion to speed.
  • Free speed, stall and free current, and the line between.
  • The same machine driving a load.
  • Power in, copper loss and shaft power.
  • Coast, dynamic braking and plugging.
  • An Uno motor dyno that measures a real motor.

Materials for the whole unit

  • Arduino Uno R3
  • Bench power supply
  • Current monitor, INA219
  • DC motor
  • DC voltage source
  • Gear motor with encoder
  • Motor driver, L9110S
  • Oscilloscope
  • Resistor x 2
  • Slide switch

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 50 min

Torque and current

Torque is current, from stall to free running.

LessonTimeWhat students do
Torque and currentA motor's torque is its current times a constant: a stalled motor at 1.2 V that cannot beat its friction, the start at 2 V, full speed at 6 V, the inrush at switch-on, and a lower-resistance winding that pulls twice the amps.50 min
  1. Run it: stalled
  2. It starts
  3. Full speed
  4. The inrush
  5. Running current
  6. A fatter winding

Materials

  • Bench power supply
  • DC motor
  • DC voltage source
  • Oscilloscope
  • Resistor x 2
  • Slide switch

Check for understanding

Each student finishes "Torque and current" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A fatter winding".

Chapter 2. About 45 min

Back EMF

A spinning motor pushes back, in proportion to speed.

LessonTimeWhat students do
Back EMFA spinning motor is a generator pushing back: speed proportional to voltage, the voltage it makes when the supply is cut, the constant that links them, and why the running current is so small.45 min
  1. Run it: half voltage
  2. Cut the supply
  3. Proportional to speed
  4. Why the current is small
  5. A better motor

Materials

  • Bench power supply
  • DC motor
  • DC voltage source
  • Oscilloscope
  • Resistor x 2
  • Slide switch

Check for understanding

Each student finishes "Back EMF" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A better motor".

Chapter 3. About 50 min

Motor curves

Free speed, stall and free current, and the line between.

LessonTimeWhat students do
Motor curvesRead a real motor's numbers off the bench: free speed, stall current and free current of a TT gear motor, the straight-line torque-speed curve they define, and a hobby motor that spins at twelve thousand rpm.50 min
  1. Run it: a TT gear motor
  2. Stall current
  3. Free current
  4. Draw the curve
  5. A 130 hobby motor
  6. A better gearmotor

Materials

  • Bench power supply
  • DC motor
  • DC voltage source
  • Oscilloscope
  • Resistor x 2
  • Slide switch

Check for understanding

Each student finishes "Motor curves" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A better gearmotor".

Chapter 4. About 35 min

Generator mode

The same machine driving a load.

LessonTimeWhat students do
Generator modeThe same machine run backward: a spinning motor driving current into a load, terminal voltage against load, the matched load that takes the most power, and the energy it is spending as it slows.35 min
  1. Run it: a light load
  2. A heavy load
  3. The matched load
  4. Load slows it

Materials

  • Bench power supply
  • DC motor
  • DC voltage source
  • Oscilloscope
  • Resistor x 2
  • Slide switch

Check for understanding

Each student finishes "Generator mode" on their own, without opening the hints. The simulator checks 4 of its 4 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Load slows it".

Chapter 5. About 45 min

Efficiency

Power in, copper loss and shaft power.

LessonTimeWhat students do
EfficiencyWhere the watts go: input power, copper loss in the winding, and the rest turned into shaft power, at full and half voltage, and what a better motor saves.45 min
  1. Run it: power in
  2. Copper loss
  3. Half voltage costs efficiency
  4. Work out the table
  5. A better motor

Materials

  • Bench power supply
  • DC motor
  • DC voltage source
  • Oscilloscope
  • Resistor x 2
  • Slide switch

Check for understanding

Each student finishes "Efficiency" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A better motor".

Chapter 6. About 35 min

Braking

Coast, dynamic braking and plugging.

LessonTimeWhat students do
BrakingThree ways to stop a motor: coast, dynamic braking with a short or a resistor, and plugging with a reversed supply that stops it and spins it the other way.35 min
  1. Run it: coast
  2. Dynamic braking
  3. Plugging
  4. It reverses

Materials

  • Bench power supply
  • DC motor
  • DC voltage source
  • Oscilloscope
  • Resistor x 2
  • Slide switch

Check for understanding

Each student finishes "Braking" on their own, without opening the hints. The simulator checks 4 of its 4 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "It reverses".

Chapter 7. About 45 min

Boss build

An Uno motor dyno that measures a real motor.

LessonTimeWhat students do
Boss: characterize a motorAn Uno, an L9110S, an INA219 and an encoder gear motor become a motor dyno: sweep the PWM, find the dead band, the free speed, the free current and the back EMF constant, then change the supply, prove the speed follows, find the driver's limit, and brake it.45 min
  1. Run it: the dyno
  2. Sweep it
  3. Read the numbers
  4. Change the supply
  5. Brake it

Materials

  • Arduino Uno R3
  • Bench power supply
  • Current monitor, INA219
  • Gear motor with encoder
  • Motor driver, L9110S

Check for understanding

Each student finishes "Boss: characterize a motor" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Brake it".

Your class

Teach this unit as a class

Start a class from this course and its 7 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.