Lesson plan

Discrete transistor design lesson plan

The building blocks inside every op-amp and audio amp, built from single transistors: current sources, mirrors, Darlingtons, the differential pair, push-pull stages, thermal stability, and a headphone amp of your own.

7 chapters, 7 lessons, about 6 hours, no board. Every lesson runs in the browser, with nothing to install.

The unit

Objectives and materials

By the end, students can

  • A transistor that holds a current, and its compliance.
  • Copy a current, the Early effect, and degeneration.
  • Gains multiplied, and what each pair costs.
  • A shared tail, gain from millivolts, common-mode rejection.
  • Class B, crossover, class AB and its idle current.
  • Bias that survives heat, and thermal runaway.
  • A two-stage discrete headphone amplifier.

Materials for the whole unit

  • Capacitor x 2
  • Component tester
  • DC voltage source x 4
  • Diode x 2
  • Function generator
  • Multimeter x 3
  • Oscilloscope
  • Resistor x 6
  • Transistor (NPN or PNP) x 6

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 55 min

Current sources

A transistor that holds a current, and its compliance.

LessonTimeWhat students do
Current sourcesA transistor that holds a current whatever the load: diode bias, an emitter resistor that sets the amps, compliance, supply rejection, and a 1 mA source designed from scratch.55 min
  1. Run it: a current, not a voltage
  2. The base reference
  3. Change the load
  4. Compliance
  5. It ignores the supply
  6. Design: a 1 mA source

Materials

  • DC voltage source
  • Diode x 2
  • Multimeter
  • Resistor x 3
  • Transistor (NPN or PNP)

Check for understanding

Each student finishes "Current sources" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Design: a 1 mA source".

Chapter 2. About 55 min

Current mirrors

Copy a current, the Early effect, and degeneration.

LessonTimeWhat students do
Current mirrorsCopy a current from one transistor to another: the diode-connected reference, a mirror that follows it, the Early effect, what a mismatched pair costs, and emitter degeneration that fixes it.55 min
  1. Run it: the reference
  2. The copy
  3. Program it with one resistor
  4. The Early effect
  5. A mismatched pair
  6. Degeneration fixes it

Materials

  • DC voltage source
  • Resistor x 4
  • Transistor (NPN or PNP) x 2

Check for understanding

Each student finishes "Current mirrors" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Degeneration fixes it".

Chapter 3. About 55 min

Darlington and Sziklai

Gains multiplied, and what each pair costs.

LessonTimeWhat students do
Darlington and SziklaiTwo transistors as one with the gains multiplied: a Darlington against a single part, its doubled base drop and high saturation, the Sziklai pair that keeps one Vbe, and a TIP120 that packs a Darlington in one case.55 min
  1. Run it: one transistor, a trickle
  2. The Darlington
  3. Two Vbe drops
  4. It never saturates hard
  5. The Sziklai pair
  6. A Darlington in a box

Materials

  • Component tester
  • DC voltage source
  • Multimeter x 3
  • Resistor x 6
  • Transistor (NPN or PNP) x 6

Check for understanding

Each student finishes "Darlington and Sziklai" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A Darlington in a box".

Chapter 4. About 55 min

Differential pair

A shared tail, gain from millivolts, common-mode rejection.

LessonTimeWhat students do
The differential pairTwo transistors sharing one tail current: the balanced split, small-signal gain measured in millivolts, full steering, common-mode rejection, and the input stage of every op-amp.55 min
  1. Run it: an even split
  2. The collector
  3. Gain from 5 millivolts
  4. Steer it all
  5. Common mode
  6. The other output

Materials

  • DC voltage source x 4
  • Multimeter x 2
  • Resistor x 3
  • Transistor (NPN or PNP) x 2

Check for understanding

Each student finishes "The differential pair" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "The other output".

Chapter 5. About 45 min

Push-pull

Class B, crossover, class AB and its idle current.

LessonTimeWhat students do
Push-pull output stagesAn NPN pushes and a PNP pulls: the dead zone of class B, crossover distortion, two diodes that bias it into class AB, its idle current, and a clean sine into a load.45 min
  1. Run it: the dead zone
  2. Class AB follows
  3. Class B loses a Vbe
  4. The idle current
  5. A clean sine

Materials

  • DC voltage source x 2
  • Diode x 2
  • Function generator
  • Multimeter x 2
  • Oscilloscope
  • Resistor x 6
  • Transistor (NPN or PNP) x 4

Check for understanding

Each student finishes "Push-pull output stages" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A clean sine".

Chapter 6. About 55 min

Thermal stability

Bias that survives heat, and thermal runaway.

LessonTimeWhat students do
Thermal stabilityWhy a hot transistor draws more current, fixed bias that runs away with beta, divider bias with an emitter resistor that holds steady, the Vbe drift of 2 mV per degree, and the loop behind thermal runaway.55 min
  1. Run it: two bias schemes
  2. The divider-biased stage
  3. Hot: the gain rises
  4. Divider bias shrugs
  5. Hot: Vbe falls
  6. Runaway in a power stage

Materials

  • DC voltage source
  • Resistor x 6
  • Transistor (NPN or PNP) x 2

Check for understanding

Each student finishes "Thermal stability" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Runaway in a power stage".

Chapter 7. About 45 min

Boss build

A two-stage discrete headphone amplifier.

LessonTimeWhat students do
Boss: a discrete headphone ampA common-emitter gain stage driving a class AB push-pull pair into a 32 ohm earpiece: check the bias, center the output, measure the gain and the power, then turn it up and find where it clips.45 min
  1. Run it: the bias point
  2. Center the output
  3. Measure the gain
  4. The power
  5. Turn it up

Materials

  • Capacitor x 2
  • DC voltage source
  • Diode x 2
  • Function generator
  • Multimeter
  • Oscilloscope
  • Resistor x 5
  • Transistor (NPN or PNP) x 3

Check for understanding

Each student finishes "Boss: a discrete headphone amp" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Turn it up".

Your class

Teach this unit as a class

Start a class from this course and its 7 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.