Lesson plan

DC circuit analysis lesson plan

Solve resistor networks on paper and prove them on the meters: KVL, KCL, series-parallel reduction, Thevenin, Norton, superposition, maximum power, and a Wheatstone bridge you turn into a sensor.

8 chapters, 8 lessons, about 6 hours, no board. Every lesson runs in the browser, with nothing to install.

The unit

Objectives and materials

By the end, students can

  • Every loop adds to zero, with one source or two.
  • What goes into a node comes out, and a resistor solved from it.
  • Collapse a network to one resistor, and an R-2R ladder.
  • Voc, Isc and Rth, measured, built and proven.
  • A current source, source transformation and compliance.
  • One source at a time, and why power does not add.
  • The matched load, and the efficiency it costs.
  • Solve, verify, balance and sense with a Wheatstone bridge.

Materials for the whole unit

  • Bench power supply
  • DC voltage source x 2
  • Multimeter x 4
  • Resistor x 10

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 45 min

KVL: the voltage law

Every loop adds to zero, with one source or two.

LessonTimeWhat students do
KVL: every loop adds to zeroKirchhoff's voltage law on a real loop: rises equal drops, any path between two points gives the same voltage, two sources aiding and opposing, and a resistor chosen so a drop lands on a target.45 min
  1. Run it: a drop across r1
  2. Rises equal drops
  3. Any path, same voltage
  4. Two sources opposing
  5. Two sources aiding
  6. Design: put 4 V on r3

Materials

  • DC voltage source x 2
  • Multimeter x 4
  • Resistor x 3

Check for understanding

Each student finishes "KVL: every loop adds to zero" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Design: put 4 V on r3".

Chapter 2. About 45 min

KCL: the current law

What goes into a node comes out, and a resistor solved from it.

LessonTimeWhat students do
KCL: what goes in comes outKirchhoff's current law at a node: an ammeter in the supply lead, branch currents read off each resistor, a new branch wired in, and a resistor solved so the supply draws a set current.45 min
  1. Run it: the supply current
  2. One branch
  3. In equals out
  4. Add a branch
  5. Solve for a resistor
  6. A current divider

Materials

  • DC voltage source
  • Multimeter
  • Resistor x 5

Check for understanding

Each student finishes "KCL: what goes in comes out" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A current divider".

Chapter 3. About 45 min

Series-parallel reduction

Collapse a network to one resistor, and an R-2R ladder.

LessonTimeWhat students do
Series-parallel reductionCollapse a network to one resistor on an ohmmeter: series adds, parallel is product over sum, equal parts halve, then an R-2R ladder that halves the voltage at every node.45 min
  1. Run it: one number for a network
  2. Series adds
  3. Parallel only ever lowers it
  4. Equal parts halve
  5. An R-2R ladder
  6. Every node halves

Materials

  • DC voltage source
  • Multimeter x 3
  • Resistor x 10

Check for understanding

Each student finishes "Series-parallel reduction" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Every node halves".

Chapter 4. About 45 min

Thevenin

Voc, Isc and Rth, measured, built and proven.

LessonTimeWhat students do
Thevenin: one source, one resistorMeasure a network's open-circuit voltage, short-circuit current and resistance with the sources off, build its Thevenin equivalent, and prove the two give the same answer under any load.45 min
  1. Run it: the open-circuit voltage
  2. Short it: the short-circuit current
  3. Kill the source: Rth
  4. Build the equivalent
  5. Prove it on the real network
  6. Predict any load

Materials

  • DC voltage source x 2
  • Multimeter x 2
  • Resistor x 6

Check for understanding

Each student finishes "Thevenin: one source, one resistor" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Predict any load".

Chapter 5. About 45 min

Norton

A current source, source transformation and compliance.

LessonTimeWhat students do
Norton: one current source, one resistorThe same network as a current source in parallel with a resistor: a bench supply in constant-current mode as the source, source transformation back to Thevenin, and what compliance voltage means.45 min
  1. Run it: the Norton current
  2. A supply as a current source
  3. Set RN
  4. Source transformation
  5. Any load again
  6. Compliance: where it stops

Materials

  • Bench power supply
  • DC voltage source
  • Multimeter x 2
  • Resistor x 5

Check for understanding

Each student finishes "Norton: one current source, one resistor" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Compliance: where it stops".

Chapter 6. About 45 min

Superposition

One source at a time, and why power does not add.

LessonTimeWhat students do
Superposition: one source at a timeTwo sources feeding one node: switch each off in turn, add the answers, predict a doubled and a reversed source by scaling, and see why power does not add the same way.45 min
  1. Run it: two sources, one node
  2. vs1 alone
  3. vs2 alone
  4. Scale one share
  5. Reverse one share
  6. Power does not add

Materials

  • DC voltage source x 2
  • Multimeter
  • Resistor x 3

Check for understanding

Each student finishes "Superposition: one source at a time" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Power does not add".

Chapter 7. About 40 min

Max power transfer

The matched load, and the efficiency it costs.

LessonTimeWhat students do
Maximum power transferSweep a load across a source with internal resistance, find the peak where the load matches it, see the 50 percent efficiency that comes with it, and match a load to a real network's Thevenin resistance.40 min
  1. Run it: a small load
  2. Match it
  3. Past the peak
  4. The cost of the peak
  5. Match a real network

Materials

  • DC voltage source x 2
  • Multimeter x 2
  • Resistor x 6

Check for understanding

Each student finishes "Maximum power transfer" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Match a real network".

Chapter 8. About 45 min

Boss build

Solve, verify, balance and sense with a Wheatstone bridge.

LessonTimeWhat students do
Boss: solve and verify a bridgeA Wheatstone bridge solved on paper and proven on the meters: its output by two dividers, its Thevenin resistance with the source off, the current in a detector, then balance it and turn it into a sensor.45 min
  1. Solve it first
  2. Verify the output
  3. Verify Rth
  4. Predict the detector current
  5. Balance it
  6. Make it a sensor

Materials

  • DC voltage source
  • Multimeter
  • Resistor x 5

Check for understanding

Each student finishes "Boss: solve and verify a bridge" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Make it a sensor".

Your class

Teach this unit as a class

Start a class from this course and its 8 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.