Lesson plan

Build a reflow oven controller lesson plan

Build the low-voltage side of a reflow oven: a thermocouple, an SSR, solder profiles, PID tracking and the safety cutoffs that make it trustworthy.

3 chapters, 6 lessons, about 6 hours, on the Arduino Uno R3. Every lesson runs in the browser, with nothing to install.

The unit

Objectives and materials

By the end, students can

  • A thermocouple in, a solid-state relay out.
  • Solder profiles, then PID to track them.
  • Cutoffs that fail safe, then a full run.

Materials for the whole unit

  • Arduino Uno R3
  • Battery: AA, coin cell, LiPo
  • Buzzer
  • Filament lamp
  • Full-size breadboard
  • Slide switch
  • Solid-state relay, SSR-25DA / G3MB-202P
  • Thermocouple converter, MAX6675

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 2 h

Measure and switch

A thermocouple in, a solid-state relay out.

LessonTimeWhat students do
ThermocouplesMeasure an oven with a type K thermocouple and a MAX6675: the microvolts at the tip, the cold junction they are measured against, quarter degree steps and an open probe.60 min
  1. Safety first
  2. Microvolts and a cold junction
  3. Reflow heat
  4. Quarter degrees
  5. A broken probe
SSR controlDrive a solid-state relay from a pin, learn why zero-cross SSRs cannot be dimmed, and control power by switching for part of each one second window.60 min
  1. No contacts
  2. Forty percent
  3. The SSR conducts
  4. The heater glows
  5. Off means off

Materials

  • Arduino Uno R3
  • Battery: AA, coin cell, LiPo
  • Buzzer
  • Filament lamp
  • Full-size breadboard
  • Slide switch
  • Solid-state relay, SSR-25DA / G3MB-202P
  • Thermocouple converter, MAX6675

Check for understanding

Each student finishes "SSR control" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Off means off".

Chapter 2. About 2 h

Follow the profile

Solder profiles, then PID to track them.

LessonTimeWhat students do
ProfilesFollow a solder profile on a simulated oven: preheat, soak, reflow above the liquidus to the peak, and cool, for lead-free and leaded paste.60 min
  1. A recipe in temperatures
  2. Preheat and soak
  3. Reflow
  4. Done, with on/off control
  5. Leaded paste
PID trackingTrack the profile with PID and feed-forward instead of on/off, and compare the overshoot, the time above liquidus and the worst error.60 min
  1. Three terms
  2. The peak
  3. Proportional power
  4. Compare
  5. Leaded, with PID

Materials

  • Arduino Uno R3
  • Battery: AA, coin cell, LiPo
  • Buzzer
  • Filament lamp
  • Full-size breadboard
  • Slide switch
  • Solid-state relay, SSR-25DA / G3MB-202P
  • Thermocouple converter, MAX6675

Check for understanding

Each student finishes "PID tracking" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Leaded, with PID".

Chapter 3. About 2 h 10 min

Make it safe

Cutoffs that fail safe, then a full run.

LessonTimeWhat students do
Safety cutoffsRing the controller with cutoffs that all fail safe: overtemp, a thermocouple fault, an open door, and a heater that does not warm the oven.60 min
  1. Hold at 150
  2. Overtemp
  3. A broken probe
  4. The door
  5. No rise
Project: a solder profileThe finished controller: pick a paste, track its profile with PID, watch the door and the thermocouple every pass, and finish with a summary and a beep.70 min
  1. Load the board
  2. A full run
  3. The door mid-run
  4. A probe fault mid-run
  5. Your paste
  6. Before a real oven

Materials

  • Arduino Uno R3
  • Battery: AA, coin cell, LiPo
  • Buzzer
  • Filament lamp
  • Full-size breadboard
  • Slide switch
  • Solid-state relay, SSR-25DA / G3MB-202P
  • Thermocouple converter, MAX6675

Check for understanding

Each student finishes "Project: a solder profile" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Before a real oven".

Your class

Teach this unit as a class

Start a class from this course and its 6 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.