Lesson plan

Build reaction training pods lesson plan

Touch pads, LED rings and a wireless pod on nRF24L01: random drills timed to the millisecond, scores and a record that survives the night.

2 chapters, 6 lessons, about 5 hours, on the Arduino Uno R3. Every lesson runs in the browser, with nothing to install.

The unit

Objectives and materials

By the end, students can

  • Touch pads, colors and a pod that talks by radio.
  • Random drills, fair scores and a full training session.

Materials for the whole unit

  • 2.4 GHz radio, nRF24L01+ x 2
  • Addressable RGB LEDs x 3
  • Arduino Uno R3 x 2
  • Touch sensor, TTP223 x 3

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 2 h 35 min

Pods

Touch pads, colors and a pod that talks by radio.

LessonTimeWhat students do
Touch padsRead TTP223 touch pads that feel a finger through plastic, with their half-second start and 60 ms answer, and light each pod's ring under a finger.55 min
  1. Three pods
  2. A finger reads HIGH
  3. Touched
  4. Ring on
  5. Let go
LightsMake the rings speak in colors: dim blue for waiting, green for go, red for a miss, with a touch on the green pod putting it out.45 min
  1. Green means go
  2. Hit it
  3. Too slow
  4. All eight green
Pods talkingLink a wireless pod with nRF24L01 radios: the hub tells pod C to light, pod C times the touch on its own clock and radios the result back.55 min
  1. The hub
  2. Pod C
  3. Light up
  4. Green over the air
  5. Timed at the pod

Materials

  • 2.4 GHz radio, nRF24L01+ x 2
  • Addressable RGB LEDs x 3
  • Arduino Uno R3 x 2
  • Touch sensor, TTP223 x 3

Check for understanding

Each student finishes "Pods talking" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Timed at the pod".

Chapter 2. About 2 h 25 min

Training

Random drills, fair scores and a full training session.

LessonTimeWhat students do
DrillsRun a drill of ten lights in random order after random gaps across all three pods, and time every reaction to the millisecond.55 min
  1. Ready
  2. Start
  3. Hit
  4. Missed
  5. Ten lights
ScoresScore a drill fairly: hits, misses counted as the full timeout, the average and the best reaction, a rating, and a record kept in EEPROM.45 min
  1. A record to beat
  2. Session over
  3. Rating
  4. New record
Project: a training sessionRun real training sessions on the three pods, see what a session of misses scores, then make the drills your own and build pods for a gym.45 min
  1. Warm up
  2. Train
  3. Hands off
  4. Build your pods

Materials

  • 2.4 GHz radio, nRF24L01+ x 2
  • Addressable RGB LEDs x 3
  • Arduino Uno R3 x 2
  • Touch sensor, TTP223 x 3

Check for understanding

Each student finishes "Project: a training session" on their own, without opening the hints. The simulator checks 4 of its 4 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Build your pods".

Your class

Teach this unit as a class

Start a class from this course and its 6 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.