nRF24 pipes
One hub, two huts: six reading pipes, the rule that pipes 2 to 5 share four address bytes with pipe 1, telling senders apart by pipe, and what happens when a hut’s pipe is closed.
Open it in the simulatorBoard to board with no router: nRF24L01+ channels, addresses, pipes, acknowledgments and retries on Unos, then ESP-NOW peers, broadcast and unicast and a star network on ESP32-C3s, ending in a base camp on Mars.
0 of 7 done
7 lessons in 4 chapters, about 6 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.
One hub, two huts: six reading pipes, the rule that pipes 2 to 5 share four address bytes with pipe 1, telling senders apart by pipe, and what happens when a hut’s pipe is closed.
Open it in the simulatorESP32-C3s talking with no router: MAC addresses, esp_now_add_peer(), a send callback that reports the receiver’s ACK, and a receive callback with the sender’s MAC and signal strength.
Open it in the simulatorA star network: three huts reporting to one hub over ESP-NOW, a table built by MAC as huts appear, message counts and missed sequence numbers, staggered timing, and a hut that goes silent.
Open it in the simulatorEach lesson opens when the one before it is done, and each chapter ends in a project.
Channels, addresses and pipes.
Two Unos, two nRF24L01+ radios, no wire: a channel, a data rate and a 5-byte address that must all match, and an automatic acknowledgment that tells the sender its ping arrived.
0 of 6 steps
One hub, two huts: six reading pipes, the rule that pipes 2 to 5 share four address bytes with pipe 1, telling senders apart by pipe, and what happens when a hut’s pipe is closed.
0 of 6 steps
Acknowledgments and retries, and ESP-NOW peers.
What the radio does when an ACK does not come: automatic retries with a delay and a count, getARC() to see how many it took, a deaf hub to watch them run out, and commands riding back on the ACKs.
0 of 7 steps
ESP32-C3s talking with no router: MAC addresses, esp_now_add_peer(), a send callback that reports the receiver’s ACK, and a receive callback with the sender’s MAC and signal strength.
0 of 6 steps
Broadcast and unicast, and a star of sensors.
One sender, two receivers: unicast to one MAC, acknowledged; broadcast to FF:FF:FF:FF:FF:FF, heard by everyone and acknowledged by nobody. When each is the right tool.
0 of 6 steps
A star network: three huts reporting to one hub over ESP-NOW, a table built by MAC as huts appear, message counts and missed sequence numbers, staggered timing, and a hut that goes silent.
0 of 6 steps
A base camp on Mars.
A habitat hub and two pods on ESP-NOW: pods unicast their oxygen levels, the hub warns of low oxygen and silent pods, and one button broadcasts a dust storm alert that every pod answers by sealing its hatch.
0 of 8 steps
All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.
Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.
Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kitYes. All 7 lessons of Wireless links: nRF24 and ESP-NOW are free and run in your browser, with nothing to install and no parts to buy before you start.
No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.
About 6 hours: 7 lessons in 4 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.
Each chapter ends in a project that puts it together: nRF24 pipes, ESP-NOW peers and Many sensors, one hub.
With "Radios and addresses", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.