All paths

Wearables and light-up clothing

Build a jacket that reacts to claps and shakes: a tiny board, a LiPo, sewn circuits, motion and sound triggers, and clothes you can wash.

Arduino NanoFree7 lessons6 h3 chapters2,076 XPMaker · Intermediate+150 XP

0 of 7 done

What you will build

3 projects, built step by step

7 lessons in 3 chapters, about 6 hours on a simulated Arduino Nano. Free, in your browser, every step checked by the simulator.

Chapter 1 project

Sewn circuits

Conductive thread is a resistor you sew. Measure the volts it drops, see why long runs limit the current, and plan the stitches.

Open it in the simulator
Chapter 2 project

Sound triggers

A KY-038 sound sensor on an interrupt: catch the first edge of a clap, ignore the rest, and count double claps.

Open it in the simulator
Chapter 3 project

Project: a reactive jacket

Put it all together: a jacket that breathes, flashes on a clap, sparkles on a shake and saves its battery when it runs low.

Open it in the simulator
The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

Power and thread

A tiny board, a LiPo budget, and the resistance of a sewn circuit.

  1. Open205 XP

    Tiny boards

    Meet the Nano, an Uno small enough to sew into a sleeve, and drive a strip of eight WS2812 LEDs from one data pin.

    0 of 5 steps

  2. Locked205 XP

    LiPo power

    A one-cell LiPo: 3.7 V, a mAh rating, a budget for the LEDs at full white and dim, and the rules for charging it safely.

    0 of 5 steps

  3. ProjectLocked410 XP

    Sewn circuits

    Conductive thread is a resistor you sew. Measure the volts it drops, see why long runs limit the current, and plan the stitches.

    0 of 5 steps

5 questions, graded as you go.
Chapter 2

Triggers

Make the lights react to a shake and to a clap.

  1. Locked205 XP

    Motion triggers

    Read an ADXL345 accelerometer register by register, turn its counts into g, and make the strip sparkle when someone shakes.

    0 of 5 steps

  2. ProjectLocked410 XP

    Sound triggers

    A KY-038 sound sensor on an interrupt: catch the first edge of a clap, ignore the rest, and count double claps.

    0 of 5 steps

4 questions, graded as you go.
Chapter 3

A reactive jacket

Comfort, washing, and the finished jacket.

  1. Locked205 XP

    Comfort and washing

    Clothes are worn for hours and washed: cap the brightness, sleep when still, and build in a wash mode that says to take the battery out.

    0 of 5 steps

  2. ProjectLocked436 XP

    Project: a reactive jacket

    Put it all together: a jacket that breathes, flashes on a clap, sparkles on a shake and saves its battery when it runs low.

    0 of 6 steps

3 questions, graded as you go.
Syllabus

Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

Power and thread

  1. Tiny boardsMeet the Nano, an Uno small enough to sew into a sleeve, and drive a strip of eight WS2812 LEDs from one data pin.
  2. LiPo powerA one-cell LiPo: 3.7 V, a mAh rating, a budget for the LEDs at full white and dim, and the rules for charging it safely.
  3. Sewn circuitsConductive thread is a resistor you sew. Measure the volts it drops, see why long runs limit the current, and plan the stitches.
Chapter 2

Triggers

  1. Motion triggersRead an ADXL345 accelerometer register by register, turn its counts into g, and make the strip sparkle when someone shakes.
  2. Sound triggersA KY-038 sound sensor on an interrupt: catch the first edge of a clap, ignore the rest, and count double claps.
Chapter 3

A reactive jacket

  1. Comfort and washingClothes are worn for hours and washed: cap the brightness, sleep when still, and build in a wash mode that says to take the battery out.
  2. Project: a reactive jacketPut it all together: a jacket that breathes, flashes on a clap, sparkles on a shake and saves its battery when it runs low.
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Wearables and light-up clothing

Is Wearables and light-up clothing free?

Yes. All 7 lessons of Wearables and light-up clothing are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Arduino Nano?

No. Every lesson runs on a simulated Arduino Nano with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Wearables and light-up clothing take?

About 6 hours: 7 lessons in 3 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: Sewn circuits, Sound triggers and Project: a reactive jacket.

Where do I start?

With "Tiny boards", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.