All paths

SPICE simulation

What a circuit simulator really does, on the SPICE engine Mokxi runs underneath: netlists, the operating point, transient and AC analysis, sweeps, models from datasheets, and a preamp verified before it is built.

Free7 lessons6 h7 chapters1,711 XPElectrical · Advanced+250 XP

0 of 7 done

What you will build

0 projects, built step by step

7 lessons in 7 chapters, about 6 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

Netlists

A circuit as text: nodes, ground and one line per part.

  1. Open265 XP

    Netlists: a circuit as text

    Read and write the text every SPICE engine runs: nodes, ground as node 0, one line per part, SPICE's 0 V ammeter, and the same divider as a canvas and as a deck.

    0 of 6 steps

3 questions, graded as you go.
Chapter 2

Operating point

Every node at DC, and where power-on differs from .op.

  1. Locked250 XP

    The operating point

    What .op solves: every node voltage of a transistor stage at once, how a bias change moves it, Mokxi's Shift+O readout, and the one place power-on and SPICE's .op disagree.

    0 of 5 steps

3 questions, graded as you go.
Chapter 3

Transient

The circuit in time, read in multiples of tau.

  1. Locked265 XP

    Transient analysis

    The circuit stepped through time: an RC fed a square wave, the time constant against the half period, what one tau, two and five look like, and the same run written as a .tran deck.

    0 of 6 steps

3 questions, graded as you go.
Chapter 4

AC sweep

A Bode plot proved point by point.

  1. Locked227 XP

    AC sweep

    What an .ac analysis computes and how a scope proves it point by point: an RC low-pass a decade above its corner, at the corner, below it, a moved corner, and the Bode plot in the Analysis sheet.

    0 of 5 steps

3 questions, graded as you go.
Chapter 5

Parameter sweeps

60 mV a decade and a Zener's knee.

  1. Locked250 XP

    Parameter sweeps

    Step one value and watch another: a transistor's current against its base voltage, 60 mV per decade, a Zener found by sweeping its supply, and the Analysis sheet's DC and parameter sweep.

    0 of 5 steps

3 questions, graded as you go.
Chapter 6

Models from datasheets

hFE, Vce(sat), GBW and the .model card.

  1. Locked227 XP

    Models from datasheets

    Turn datasheet numbers into model parameters: hFE into beta, Vce(sat) at its test condition, an op-amp's gain-bandwidth product checked at its own bandwidth, and the .model card behind it all.

    0 of 5 steps

3 questions, graded as you go.
Chapter 7

Boss build

Predict, verify and change a preamp before you build it.

  1. Locked227 XP

    Boss: verify before you build

    Design a microphone preamp on paper, predict its operating point and gain, verify every number in the simulator, then change the design to a new spec and verify again before a single part is bought.

    0 of 5 steps

3 questions, graded as you go.
Syllabus

Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

Netlists

  1. Netlists: a circuit as textRead and write the text every SPICE engine runs: nodes, ground as node 0, one line per part, SPICE's 0 V ammeter, and the same divider as a canvas and as a deck.
Chapter 2

Operating point

  1. The operating pointWhat .op solves: every node voltage of a transistor stage at once, how a bias change moves it, Mokxi's Shift+O readout, and the one place power-on and SPICE's .op disagree.
Chapter 3

Transient

  1. Transient analysisThe circuit stepped through time: an RC fed a square wave, the time constant against the half period, what one tau, two and five look like, and the same run written as a .tran deck.
Chapter 4

AC sweep

  1. AC sweepWhat an .ac analysis computes and how a scope proves it point by point: an RC low-pass a decade above its corner, at the corner, below it, a moved corner, and the Bode plot in the Analysis sheet.
Chapter 5

Parameter sweeps

  1. Parameter sweepsStep one value and watch another: a transistor's current against its base voltage, 60 mV per decade, a Zener found by sweeping its supply, and the Analysis sheet's DC and parameter sweep.
Chapter 6

Models from datasheets

  1. Models from datasheetsTurn datasheet numbers into model parameters: hFE into beta, Vce(sat) at its test condition, an op-amp's gain-bandwidth product checked at its own bandwidth, and the .model card behind it all.
Chapter 7

Boss build

  1. Boss: verify before you buildDesign a microphone preamp on paper, predict its operating point and gain, verify every number in the simulator, then change the design to a new spec and verify again before a single part is bought.
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About SPICE simulation

Is SPICE simulation free?

Yes. All 7 lessons of SPICE simulation are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does SPICE simulation take?

About 6 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Netlists: a circuit as text", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.