All paths

Build a spaceship control panel

Arming switches, a mission display, a countdown, an engine and a master alarm, then fly the whole panel to orbit.

Arduino Mega 2560Free7 lessons5 h4 chapters2,538 XPMaker · Advanced+250 XP

0 of 7 done

Start the course freeArming switches with lit buttonsBuild it as a kitRetails for about $109, free on Mokxi.Lesson plan for teachers
What you will build

3 projects, built step by step

7 lessons in 4 chapters, about 5 hours on a simulated Arduino Mega 2560. Free, in your browser, every step checked by the simulator.

Chapter 1 project

A mission display and a throttle

Add a 20 x 4 LCD that shows the pre-flight checklist, and a slide-pot throttle that has to sit at minimum before the checklist completes.

Open it in the simulator
Chapter 2 project

Engine glow and thrust against weight

A ring of 16 NeoPixels flickers like an engine bell as the throttle opens, and the LCD shows when thrust beats weight and the rocket would climb.

Open it in the simulator
Chapter 3 project

A master alarm drill

Turn three systems on and a fault trips the master alarm: silence it with the red button, read the fix on the LCD, and cycle the right switch.

Open it in the simulator
The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

Arm the ship

Two-step arming with lit buttons, and a display that tells the truth.

  1. Open250 XP

    Arming switches with lit buttons

    Three toggles and three lit arcade buttons on a Mega. Flip a switch and its lamp asks, press the lamp and it answers: two-step arming, the way real panels guard against a stray hand.

    0 of 5 steps

  2. ProjectLocked424 XP

    A mission display and a throttle

    Add a 20 x 4 LCD that shows the pre-flight checklist, and a slide-pot throttle that has to sit at minimum before the checklist completes.

    0 of 4 steps

Chapter 2

Count it down

A guarded launch button, a countdown that holds, and an engine that glows.

  1. Locked288 XP

    A safety switch and a countdown

    A LAUNCH button that only works with the MASTER ARM safety up, and a TM1637 that counts down from T-10 and holds if the safety drops.

    0 of 6 steps

  2. ProjectLocked424 XP

    Engine glow and thrust against weight

    A ring of 16 NeoPixels flickers like an engine bell as the throttle opens, and the LCD shows when thrust beats weight and the rocket would climb.

    0 of 4 steps

Chapter 3

Gauges and alarms

Read fuel and pitch at a glance, and stay calm when the alarm goes.

  1. Locked250 XP

    A fuel gauge and a pitch needle

    A practice burn on the pad: the throttle drains a ten-bar fuel gauge, a servo needle shows the pitch tipping toward the horizon, and the stick trims it.

    0 of 5 steps

  2. ProjectLocked576 XP

    A master alarm drill

    Turn three systems on and a fault trips the master alarm: silence it with the red button, read the fix on the LCD, and cycle the right switch.

    0 of 6 steps

Chapter 4

Fly to orbit

Everything at once, from checklist to orbit.

  1. Locked326 XP

    Fly to orbit

    The finished panel: checklist, go/no-go poll, countdown, liftoff, staging and a fault or two on the way to orbit, with real orbital math deciding when you are there.

    0 of 7 steps

Syllabus

Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

Arm the ship

  1. Arming switches with lit buttonsThree toggles and three lit arcade buttons on a Mega. Flip a switch and its lamp asks, press the lamp and it answers: two-step arming, the way real panels guard against a stray hand.
  2. A mission display and a throttleAdd a 20 x 4 LCD that shows the pre-flight checklist, and a slide-pot throttle that has to sit at minimum before the checklist completes.
Chapter 2

Count it down

  1. A safety switch and a countdownA LAUNCH button that only works with the MASTER ARM safety up, and a TM1637 that counts down from T-10 and holds if the safety drops.
  2. Engine glow and thrust against weightA ring of 16 NeoPixels flickers like an engine bell as the throttle opens, and the LCD shows when thrust beats weight and the rocket would climb.
Chapter 3

Gauges and alarms

  1. A fuel gauge and a pitch needleA practice burn on the pad: the throttle drains a ten-bar fuel gauge, a servo needle shows the pitch tipping toward the horizon, and the stick trims it.
  2. A master alarm drillTurn three systems on and a fault trips the master alarm: silence it with the red button, read the fix on the LCD, and cycle the right switch.
Chapter 4

Fly to orbit

  1. Fly to orbitThe finished panel: checklist, go/no-go poll, countdown, liftoff, staging and a fault or two on the way to orbit, with real orbital math deciding when you are there.
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

The kit for this course

Spaceship Panel Kit

A Mega, arming switches, a throttle, a countdown clock, an engine ring, gauges and a launch button.

Open the kit
Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Build a spaceship control panel

Is Build a spaceship control panel free?

Yes. All 7 lessons of Build a spaceship control panel are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Arduino Mega 2560?

No. Every lesson runs on a simulated Arduino Mega 2560 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Build a spaceship control panel take?

About 5 hours: 7 lessons in 4 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: A mission display and a throttle, Engine glow and thrust against weight and A master alarm drill.

Where do I start?

With "Arming switches with lit buttons", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.