All paths

Sensor signal conditioning

Advanced, after Sensors and measurement: bridges on long cables, load cells and the HX711, thermocouples, RTDs, offset and gain, anti-alias filters, and a precision scale built two ways.

Free7 lessons6 h7 chapters2,107 XPElectrical · Advanced+250 XP

0 of 7 done

Start the course freeWheatstone bridges in practiceLesson plan for teachers
What you will build

0 projects, built step by step

7 lessons in 7 chapters, about 6 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

Wheatstone bridges

Millivolts per volt, lead wires and shunt calibration.

  1. Open326 XP

    Wheatstone bridges in practice

    A strain gauge on the end of a cable: millivolts per volt, a bridge that is not quite linear, lead wires that fake a strain, the three-wire fix, and a shunt resistor that calibrates without a weight.

    0 of 7 steps

4 questions, graded as you go.
Chapter 2

Load cells

The counts behind a gram, and choosing a cell.

  1. Locked250 XP

    Load cells and the HX711

    A load cell is a bridge in a block of aluminum, read by a 24-bit HX711: the counts behind a gram, the wrong cell for the job, why mV/V over capacity is the number that matters, and what happens past the input range.

    0 of 5 steps

3 questions, graded as you go.
Chapter 3

Thermocouples

The cold junction, the curve and a MAX31855.

  1. Locked326 XP

    Thermocouples

    A type K thermocouple on an OP07 at 10 mV per degree: the cold junction that steals 25 degrees, compensation that tracks the room, the curve that bends at 500 C, and a MAX31855 that does it all in a chip.

    0 of 7 steps

4 questions, graded as you go.
Chapter 4

RTDs

Platinum, four wires and a MAX31865.

  1. Locked326 XP

    RTDs: platinum and four wires

    A PT100 fed 1 mA by an LM358: 100 ohms at 0 C and 138.5 at 100 C, two lead wires that add 6.7 degrees, the four-wire measurement that ignores them, self-heating, and a MAX31865 in a chip.

    0 of 7 steps

4 questions, graded as you go.
Chapter 5

Offset and gain

Zero and span onto an ADC, and the rails that stop you.

  1. Locked288 XP

    Offset and gain

    An LM35 mapped onto an ADC by an LM358 difference amp: gain is the span, the reference is the zero, an output that cannot go below its ground, a re-zero and a re-span, and the ceiling of a single supply.

    0 of 6 steps

4 questions, graded as you go.
Chapter 6

Anti-alias filters

Nyquist, folding and a two-pole filter before the ADC.

  1. Locked288 XP

    Anti-alias filters

    An ADC folds anything above half its sample rate back down as a fake low tone. One RC against a two-pole Sallen-Key on an LM358: both -3 dB at 100 Hz, a tenth against a hundredth at 1 kHz, a corner moved, and the wrong capacitors.

    0 of 6 steps

4 questions, graded as you go.
Chapter 7

Boss build

A precision scale, analog and on a chip.

  1. Locked303 XP

    Boss build: a precision scale

    A load cell read two ways: an LM358 two-op-amp in-amp at a gain of 201 into a low pass for a 10-bit ADC, and an HX711 beside it. Weigh 2.5 kg on both, trim out a cell's zero error, and re-design the analog channel for a 20 kg cell.

    0 of 7 steps

3 questions, graded as you go.
Syllabus

Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

Wheatstone bridges

  1. Wheatstone bridges in practiceA strain gauge on the end of a cable: millivolts per volt, a bridge that is not quite linear, lead wires that fake a strain, the three-wire fix, and a shunt resistor that calibrates without a weight.
Chapter 2

Load cells

  1. Load cells and the HX711A load cell is a bridge in a block of aluminum, read by a 24-bit HX711: the counts behind a gram, the wrong cell for the job, why mV/V over capacity is the number that matters, and what happens past the input range.
Chapter 3

Thermocouples

  1. ThermocouplesA type K thermocouple on an OP07 at 10 mV per degree: the cold junction that steals 25 degrees, compensation that tracks the room, the curve that bends at 500 C, and a MAX31855 that does it all in a chip.
Chapter 4

RTDs

  1. RTDs: platinum and four wiresA PT100 fed 1 mA by an LM358: 100 ohms at 0 C and 138.5 at 100 C, two lead wires that add 6.7 degrees, the four-wire measurement that ignores them, self-heating, and a MAX31865 in a chip.
Chapter 5

Offset and gain

  1. Offset and gainAn LM35 mapped onto an ADC by an LM358 difference amp: gain is the span, the reference is the zero, an output that cannot go below its ground, a re-zero and a re-span, and the ceiling of a single supply.
Chapter 6

Anti-alias filters

  1. Anti-alias filtersAn ADC folds anything above half its sample rate back down as a fake low tone. One RC against a two-pole Sallen-Key on an LM358: both -3 dB at 100 Hz, a tenth against a hundredth at 1 kHz, a corner moved, and the wrong capacitors.
Chapter 7

Boss build

  1. Boss build: a precision scaleA load cell read two ways: an LM358 two-op-amp in-amp at a gain of 201 into a low pass for a 10-bit ADC, and an HX711 beside it. Weigh 2.5 kg on both, trim out a cell's zero error, and re-design the analog channel for a 20 kg cell.
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Sensor signal conditioning

Is Sensor signal conditioning free?

Yes. All 7 lessons of Sensor signal conditioning are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does Sensor signal conditioning take?

About 6 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Wheatstone bridges in practice", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.