All paths

Protection circuits

Keep a mistake from killing your electronics: fuses and resettable limits, reverse polarity, surge clamps, inrush limiting, flyback clamps, crowbars, and a power input you harden against all of it.

Free7 lessons5 h7 chapters1,417 XPElectrical · Intermediate+150 XP

0 of 7 done

What you will build

0 projects, built step by step

7 lessons in 7 chapters, about 5 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

Fuses and PTCs

One-shot fuses against resettable limits.

  1. Open205 XP

    Fuses and resettable limits

    A one-shot fuse against a resettable limit: a 2 A fuse that opens on a short and stays open, a current limit that holds a short at a safe current, the rail it collapses, and the recovery a PTC or eFuse gives you.

    0 of 5 steps

3 questions, graded as you go.
Chapter 2

Reverse polarity

A series diode and a P-MOSFET.

  1. Locked205 XP

    Reverse polarity

    Two ways to survive a battery put in backward: a series Schottky diode and what it costs in volts, and a P-channel MOSFET that does the same with almost no loss, blocking either way around.

    0 of 5 steps

3 questions, graded as you go.
Chapter 3

TVS and ESD

Clamp a surge, and what ESD needs.

  1. Locked218 XP

    TVS and ESD

    A surge on a supply line burns out an unprotected lamp; a clamp diode across the rail holds it at a safe voltage and takes the current instead; and what ESD is, and why it needs a faster part than the simulator models.

    0 of 6 steps

3 questions, graded as you go.
Chapter 4

Inrush limiting

A limiter, its cost, and the bypass.

  1. Locked205 XP

    Inrush limiting

    A big input capacitor that blows the fuse at switch-on, a limiter resistor (an NTC's cold resistance) that stops it, the power the limiter wastes once running, and the bypass that takes it out of the circuit.

    0 of 5 steps

3 questions, graded as you go.
Chapter 5

Flyback diodes

A diode clamp and a diode-Zener clamp.

  1. Locked174 XP

    Flyback clamps

    The coil kick from the magnetism course, clamped two ways: a plain flyback diode that holds the drain one drop above the supply, and a diode-Zener clamp that lets it rise to a set voltage to dump the energy faster.

    0 of 4 steps

3 questions, graded as you go.
Chapter 6

Crowbars

Sense, short, and let the fuse clear it.

  1. Locked205 XP

    Crowbars

    An overvoltage crowbar: a Zener that senses the rail, a switch that shorts it, and the fuse that clears the fault, then the same crowbar on a current-limited supply, and how the trip point is chosen.

    0 of 5 steps

3 questions, graded as you go.
Chapter 7

Boss build

A bulletproof 12 V input.

  1. Locked205 XP

    Boss: a bulletproof power input

    One 12 V input hardened against everything in the course: a fuse, a P-MOSFET for reverse polarity and a clamp for surges in front of a lamp, then test it backward, surged and shorted, and retune the clamp for 16 V parts.

    0 of 5 steps

3 questions, graded as you go.
Syllabus

Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

Fuses and PTCs

  1. Fuses and resettable limitsA one-shot fuse against a resettable limit: a 2 A fuse that opens on a short and stays open, a current limit that holds a short at a safe current, the rail it collapses, and the recovery a PTC or eFuse gives you.
Chapter 2

Reverse polarity

  1. Reverse polarityTwo ways to survive a battery put in backward: a series Schottky diode and what it costs in volts, and a P-channel MOSFET that does the same with almost no loss, blocking either way around.
Chapter 3

TVS and ESD

  1. TVS and ESDA surge on a supply line burns out an unprotected lamp; a clamp diode across the rail holds it at a safe voltage and takes the current instead; and what ESD is, and why it needs a faster part than the simulator models.
Chapter 4

Inrush limiting

  1. Inrush limitingA big input capacitor that blows the fuse at switch-on, a limiter resistor (an NTC's cold resistance) that stops it, the power the limiter wastes once running, and the bypass that takes it out of the circuit.
Chapter 5

Flyback diodes

  1. Flyback clampsThe coil kick from the magnetism course, clamped two ways: a plain flyback diode that holds the drain one drop above the supply, and a diode-Zener clamp that lets it rise to a set voltage to dump the energy faster.
Chapter 6

Crowbars

  1. CrowbarsAn overvoltage crowbar: a Zener that senses the rail, a switch that shorts it, and the fuse that clears the fault, then the same crowbar on a current-limited supply, and how the trip point is chosen.
Chapter 7

Boss build

  1. Boss: a bulletproof power inputOne 12 V input hardened against everything in the course: a fuse, a P-MOSFET for reverse polarity and a clamp for surges in front of a lamp, then test it backward, surged and shorted, and retune the clamp for 16 V parts.
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Protection circuits

Is Protection circuits free?

Yes. All 7 lessons of Protection circuits are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does Protection circuits take?

About 5 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Fuses and resettable limits", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.