All paths

Op-amp circuit cookbook

Advanced, after Transistors and op-amps for real: the integrator, differentiator, summing amp, instrumentation amp, precision rectifier and oscillators, ending in a strain gauge front end you scale yourself.

Free7 lessons6 h7 chapters1,939 XPElectrical · Advanced+250 XP

0 of 7 done

What you will build

0 projects, built step by step

7 lessons in 7 chapters, about 6 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

Integrator

A capacitor in the feedback: the running total of the input.

  1. Open288 XP

    Integrator

    A TL072 with a capacitor for feedback: a gain of exactly 1 at 159 Hz that halves every time the frequency doubles, a square wave turned into a triangle, and the 1 M resistor that keeps a tiny DC offset from slamming it into a rail.

    0 of 6 steps

4 questions, graded as you go.
Chapter 2

Differentiator

A capacitor on the input: how fast the input moves, and its noise.

  1. Locked265 XP

    Differentiator

    Swap the capacitor and resistor: a gain that rises with frequency, 1 at 159 Hz and 2 at 318, a triangle turned into a square, and the series resistor that keeps it from amplifying every bit of noise.

    0 of 6 steps

3 questions, graded as you go.
Chapter 3

Summing amp

Inputs that add at a virtual ground, and a 3-bit DAC.

  1. Locked265 XP

    Summing amp

    An NE5532 adding three inputs at a virtual ground: binary-weighted resistors make a 3-bit DAC, every input adds without touching the others, and one resistor sets the full scale.

    0 of 6 steps

3 questions, graded as you go.
Chapter 4

Instrumentation amp

Millivolts from a bridge, with the common part thrown away.

  1. Locked265 XP

    Instrumentation amp

    A strain gauge bridge gives 12 mV on top of 2.5 V: two OP07 buffers and a difference stage amplify the 12 mV and ignore the 2.5 V, one resistor sets the gain, and an op-amp's offset shows why precision parts exist.

    0 of 6 steps

4 questions, graded as you go.
Chapter 5

Precision rectifier

Diodes inside the loop, and an absolute value circuit.

  1. Locked265 XP

    Precision rectifier

    A 0.3 V signal that a plain diode cannot rectify at all: diodes inside an op-amp's feedback lose their 0.6 V, a half-wave stage and a summing stage make a full-wave absolute value, and one wrong resistor breaks it.

    0 of 6 steps

3 questions, graded as you go.
Chapter 6

Oscillators

A relaxation square wave and a Wien bridge sine.

  1. Locked288 XP

    Oscillators

    Two oscillators on one TL072: a relaxation square wave at 451 Hz that halves with twice the capacitor, and a Wien bridge sine at 158 Hz that lives on a gain of exactly 3 and dies on 2.8.

    0 of 6 steps

4 questions, graded as you go.
Chapter 7

Boss build

A strain gauge front end for a 0 to 5 V ADC.

  1. Locked303 XP

    Boss build: a strain gauge front end

    A bridge on a long, humming cable into an in-amp sitting on a 2.5 V reference and a 16 Hz low pass: reject the hum, scale the gauge to fill a 0 to 5 V ADC both ways, then re-design it for a gauge four times less sensitive.

    0 of 7 steps

4 questions, graded as you go.
Syllabus

Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

Integrator

  1. IntegratorA TL072 with a capacitor for feedback: a gain of exactly 1 at 159 Hz that halves every time the frequency doubles, a square wave turned into a triangle, and the 1 M resistor that keeps a tiny DC offset from slamming it into a rail.
Chapter 2

Differentiator

  1. DifferentiatorSwap the capacitor and resistor: a gain that rises with frequency, 1 at 159 Hz and 2 at 318, a triangle turned into a square, and the series resistor that keeps it from amplifying every bit of noise.
Chapter 3

Summing amp

  1. Summing ampAn NE5532 adding three inputs at a virtual ground: binary-weighted resistors make a 3-bit DAC, every input adds without touching the others, and one resistor sets the full scale.
Chapter 4

Instrumentation amp

  1. Instrumentation ampA strain gauge bridge gives 12 mV on top of 2.5 V: two OP07 buffers and a difference stage amplify the 12 mV and ignore the 2.5 V, one resistor sets the gain, and an op-amp's offset shows why precision parts exist.
Chapter 5

Precision rectifier

  1. Precision rectifierA 0.3 V signal that a plain diode cannot rectify at all: diodes inside an op-amp's feedback lose their 0.6 V, a half-wave stage and a summing stage make a full-wave absolute value, and one wrong resistor breaks it.
Chapter 6

Oscillators

  1. OscillatorsTwo oscillators on one TL072: a relaxation square wave at 451 Hz that halves with twice the capacitor, and a Wien bridge sine at 158 Hz that lives on a gain of exactly 3 and dies on 2.8.
Chapter 7

Boss build

  1. Boss build: a strain gauge front endA bridge on a long, humming cable into an in-amp sitting on a 2.5 V reference and a 16 Hz low pass: reject the hum, scale the gauge to fill a 0 to 5 V ADC both ways, then re-design it for a gauge four times less sensitive.
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Op-amp circuit cookbook

Is Op-amp circuit cookbook free?

Yes. All 7 lessons of Op-amp circuit cookbook are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does Op-amp circuit cookbook take?

About 6 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Integrator", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.