All paths

Magnetism and inductors

Coils as magnets and as inductors: force and the square law, L over R, the flyback spike and its diode, Hall sensors, reed switches, solenoids, and an Uno that sorts parts by their magnets.

Free7 lessons5 h7 chapters1,448 XPElectrical · Intermediate+150 XP

0 of 7 done

What you will build

0 projects, built step by step

7 lessons in 7 chapters, about 5 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

Fields and coils

Current makes a field, and force goes with its square.

  1. Open236 XP

    Fields and coils

    A coil is a magnet you can switch: force from current, the square law, a pole that flips with the current but still pulls, steel that saturates, and the least voltage that holds a load.

    0 of 6 steps

3 questions, graded as you go.
Chapter 2

Inductance

A coil resists a change in current: L over R.

  1. Locked205 XP

    Inductance

    A coil fights a change in its current: L / R as a time constant, the voltage jump at every edge, the current's climb in one tau and five, and a smaller coil that keeps up.

    0 of 5 steps

3 questions, graded as you go.
Chapter 3

Back EMF and flyback

The spike at switch-off and the diode that stops it.

  1. Locked187 XP

    Back EMF and flyback

    Switch a solenoid with a MOSFET: its pull-in current, the spike when the current is cut, and the flyback diode that gives the coil's current somewhere to go.

    0 of 5 steps

3 questions, graded as you go.
Chapter 4

Hall sensors

Linear and switching, both poles and one, and hysteresis.

  1. Locked236 XP

    Hall sensors

    A linear 49E that reads gauss and pole on a meter, an A3144 switch that sees only a south pole, and the hysteresis that keeps it from chattering.

    0 of 6 steps

3 questions, graded as you go.
Chapter 5

Reed switches

Blades in glass, closing and opening distances.

  1. Locked174 XP

    Reed switches

    Two steel blades in glass that a magnet pulls shut: the closing distance, the wider opening distance, and how to set the sensitivity of a door sensor.

    0 of 4 steps

3 questions, graded as you go.
Chapter 6

Solenoids and electromagnets

Real coil actuators and what they draw.

  1. Locked174 XP

    Solenoids and electromagnets

    A real 12 V door lock and a 5 V holding magnet: pull-in, the current a coil really draws, the square law on a 3.3 V supply, and why both need a transistor and a diode.

    0 of 4 steps

3 questions, graded as you go.
Chapter 7

Boss build

Sort parts by their magnets, then tune it.

  1. Locked236 XP

    Boss: a magnetic sorter

    An Uno sorts parts by their magnets: a linear Hall sensor reads pole and strength, a Hall switch confirms, a reed counts, a solenoid kicks south parts and an electromagnet holds north ones. Then tune its threshold.

    0 of 6 steps

3 questions, graded as you go.
Syllabus

Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

Fields and coils

  1. Fields and coilsA coil is a magnet you can switch: force from current, the square law, a pole that flips with the current but still pulls, steel that saturates, and the least voltage that holds a load.
Chapter 2

Inductance

  1. InductanceA coil fights a change in its current: L / R as a time constant, the voltage jump at every edge, the current's climb in one tau and five, and a smaller coil that keeps up.
Chapter 3

Back EMF and flyback

  1. Back EMF and flybackSwitch a solenoid with a MOSFET: its pull-in current, the spike when the current is cut, and the flyback diode that gives the coil's current somewhere to go.
Chapter 4

Hall sensors

  1. Hall sensorsA linear 49E that reads gauss and pole on a meter, an A3144 switch that sees only a south pole, and the hysteresis that keeps it from chattering.
Chapter 5

Reed switches

  1. Reed switchesTwo steel blades in glass that a magnet pulls shut: the closing distance, the wider opening distance, and how to set the sensitivity of a door sensor.
Chapter 6

Solenoids and electromagnets

  1. Solenoids and electromagnetsA real 12 V door lock and a 5 V holding magnet: pull-in, the current a coil really draws, the square law on a 3.3 V supply, and why both need a transistor and a diode.
Chapter 7

Boss build

  1. Boss: a magnetic sorterAn Uno sorts parts by their magnets: a linear Hall sensor reads pole and strength, a Hall switch confirms, a reed counts, a solenoid kicks south parts and an electromagnet holds north ones. Then tune its threshold.
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Magnetism and inductors

Is Magnetism and inductors free?

Yes. All 7 lessons of Magnetism and inductors are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does Magnetism and inductors take?

About 5 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Fields and coils", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.