All paths

Build your own fight stick

One button to a full leverless controller on a Pico: SOCD, eight buttons, lit buttons, an OLED and modes.

Raspberry Pi PicoFree5 lessons4 h2 chapters1,604 XPMaker · Advanced+250 XP

0 of 5 done

Start the course freeOne button, read like a controllerBuild it as a kitRetails for about $55, free on Mokxi.Lesson plan for teachers
What you will build

2 projects, built step by step

5 lessons in 2 chapters, about 4 hours on a simulated Raspberry Pi Pico. Free, in your browser, every step checked by the simulator.

Chapter 1 project

All eight attack buttons

Add the eight attack buttons in the two-row layout, keep the pins and names in one table, and report every combination at once.

Open it in the simulator
Chapter 2 project

The full controller

Add the OLED input display, Select, Start, Home and turbo, switch SOCD and stick modes with GP2040-CE's combos, and make the template yours.

Open it in the simulator
The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

The inputs

A button, the directions with SOCD cleaning, then all eight attacks.

  1. Open227 XP

    One button, read like a controller

    Wire a 30 mm LED arcade button to a Pico, light its lamp, and debounce it the way controller firmware does: no added lag at all.

    0 of 5 steps

  2. Locked242 XP

    Four directions and SOCD cleaning

    Wire the left-hand cluster of a leverless controller, report it in numpad notation, and clean left + right the way tournament rules ask.

    0 of 6 steps

  3. ProjectLocked454 XP

    All eight attack buttons

    Add the eight attack buttons in the two-row layout, keep the pins and names in one table, and report every combination at once.

    0 of 5 steps

Chapter 2

The finish

Lit buttons, a screen, mode combos and turbo: the flagship template.

  1. Locked227 XP

    Lit buttons with themes

    Swap in LED arcade buttons, fade each lamp with PWM on its own pin, and give the controller themes that react to every press.

    0 of 5 steps

  2. ProjectLocked454 XP

    The full controller

    Add the OLED input display, Select, Start, Home and turbo, switch SOCD and stick modes with GP2040-CE's combos, and make the template yours.

    0 of 5 steps

Syllabus

Every lesson in the course

All 5 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

The inputs

  1. One button, read like a controllerWire a 30 mm LED arcade button to a Pico, light its lamp, and debounce it the way controller firmware does: no added lag at all.
  2. Four directions and SOCD cleaningWire the left-hand cluster of a leverless controller, report it in numpad notation, and clean left + right the way tournament rules ask.
  3. All eight attack buttonsAdd the eight attack buttons in the two-row layout, keep the pins and names in one table, and report every combination at once.
Chapter 2

The finish

  1. Lit buttons with themesSwap in LED arcade buttons, fade each lamp with PWM on its own pin, and give the controller themes that react to every press.
  2. The full controllerAdd the OLED input display, Select, Start, Home and turbo, switch SOCD and stick modes with GP2040-CE's combos, and make the template yours.
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

The kit for this course

Fight Stick Kit

A Pico, a leverless layout of arcade buttons, lit caps and a little OLED screen.

Open the kit
Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Build your own fight stick

Is Build your own fight stick free?

Yes. All 5 lessons of Build your own fight stick are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Raspberry Pi Pico?

No. Every lesson runs on a simulated Raspberry Pi Pico with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Build your own fight stick take?

About 4 hours: 5 lessons in 2 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: All eight attack buttons and The full controller.

Where do I start?

With "One button, read like a controller", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.