All paths

ADCs, DACs and sampling

What a converter really gives you: aliasing, resolution and the LSB, R-2R and PWM DACs, the ADS1115, MCP3008 and MCP4725, and a 16-bit voltmeter that checks itself.

Free7 lessons6 h7 chapters1,940 XPElectrical · Advanced+250 XP

0 of 7 done

Start the course freeAliasing: when a fast signal looks slowLesson plan for teachers
What you will build

0 projects, built step by step

7 lessons in 7 chapters, about 6 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

Aliasing

Sample below twice the signal and it lies.

  1. Open288 XP

    Aliasing: when a fast signal looks slow

    An Uno samples a sine from a function generator at a rate you pick and counts the cycles it sees: right below half the sample rate, wrong above it, with the Nyquist rule and the anti-alias filter that real converters put first.

    0 of 6 steps

4 questions, graded as you go.
Chapter 2

Resolution and LSB

Codes, steps, bits, references and clipping.

  1. Locked288 XP

    Resolution and LSB: the smallest step

    A bench supply on A0: the code and the volts, one LSB of 4.88 mV, a change too small to see, fewer bits and bigger steps, the 1.1 V reference for finer ones, and what happens past full scale.

    0 of 6 steps

4 questions, graded as you go.
Chapter 3

R-2R DAC

Binary weights from two resistor values, and why it needs a buffer.

  1. Locked288 XP

    R-2R DAC: bits into volts with two resistor values

    Four slide switches drive a 10k and 20k ladder: each bit worth half the one above it, the LSB, full scale one step short of 5 V, a predicted code, and why a ladder needs a buffer.

    0 of 6 steps

4 questions, graded as you go.
Chapter 4

PWM as a DAC

A pin and an RC filter: level, ripple and step.

  1. Locked288 XP

    PWM as a DAC: a pin and a filter

    Pin 9's PWM through a 10k and 10 uF low-pass: the duty sets the voltage, the pin still switches, a smaller capacitor shows the ripple, a predicted level, and the 19.6 mV step of 8-bit PWM.

    0 of 6 steps

3 questions, graded as you go.
Chapter 5

ADS1115 and MCP3008

Sixteen bits and a gain amplifier against ten bits and speed.

  1. Locked250 XP

    ADS1115 and MCP3008: buying more bits

    A 16-bit ADS1115 on I2C and a 10-bit MCP3008 on SPI read the same input: a change only one of them sees, clipping past the range, a programmable gain that makes 0.1 V worth 12,800 counts, and the speed each trades.

    0 of 5 steps

4 questions, graded as you go.
Chapter 6

MCP4725

A 12-bit DAC on I2C, read back and compared with PWM.

  1. Locked250 XP

    MCP4725: a real DAC on I2C

    The gallery's DAC sine: a 12-bit MCP4725 writes a 32-point sine, A0 reads it back, and pin 9 plays the same sine as PWM for comparison on the scope.

    0 of 5 steps

3 questions, graded as you go.
Chapter 7

Boss build

A 0 to 30 V meter with a divider, a self-test and a range you pick.

  1. Locked288 XP

    Boss: a 16-bit voltmeter

    An ADS1115 meter for 0 to 30 V: wire a bussed resistor network as an 8:1 divider, tell the sketch the ratio, check it against an MCP4725 self-test, and pick the range that fits.

    0 of 6 steps

4 questions, graded as you go.
Syllabus

Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

Aliasing

  1. Aliasing: when a fast signal looks slowAn Uno samples a sine from a function generator at a rate you pick and counts the cycles it sees: right below half the sample rate, wrong above it, with the Nyquist rule and the anti-alias filter that real converters put first.
Chapter 2

Resolution and LSB

  1. Resolution and LSB: the smallest stepA bench supply on A0: the code and the volts, one LSB of 4.88 mV, a change too small to see, fewer bits and bigger steps, the 1.1 V reference for finer ones, and what happens past full scale.
Chapter 3

R-2R DAC

  1. R-2R DAC: bits into volts with two resistor valuesFour slide switches drive a 10k and 20k ladder: each bit worth half the one above it, the LSB, full scale one step short of 5 V, a predicted code, and why a ladder needs a buffer.
Chapter 4

PWM as a DAC

  1. PWM as a DAC: a pin and a filterPin 9's PWM through a 10k and 10 uF low-pass: the duty sets the voltage, the pin still switches, a smaller capacitor shows the ripple, a predicted level, and the 19.6 mV step of 8-bit PWM.
Chapter 5

ADS1115 and MCP3008

  1. ADS1115 and MCP3008: buying more bitsA 16-bit ADS1115 on I2C and a 10-bit MCP3008 on SPI read the same input: a change only one of them sees, clipping past the range, a programmable gain that makes 0.1 V worth 12,800 counts, and the speed each trades.
Chapter 6

MCP4725

  1. MCP4725: a real DAC on I2CThe gallery's DAC sine: a 12-bit MCP4725 writes a 32-point sine, A0 reads it back, and pin 9 plays the same sine as PWM for comparison on the scope.
Chapter 7

Boss build

  1. Boss: a 16-bit voltmeterAn ADS1115 meter for 0 to 30 V: wire a bussed resistor network as an 8:1 divider, tell the sketch the ratio, check it against an MCP4725 self-test, and pick the range that fits.
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About ADCs, DACs and sampling

Is ADCs, DACs and sampling free?

Yes. All 7 lessons of ADCs, DACs and sampling are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does ADCs, DACs and sampling take?

About 6 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Aliasing: when a fast signal looks slow", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.