Drawing shapes
A night launch in pixels: coordinates where y grows down, lines, rectangles, circles and triangles, colors as RGB565 numbers, and a satellite animated by erasing and redrawing.
Open it in the simulatorMake touch-screen gadgets on the Cheap Yellow Display, an ESP32 with a screen built in: shapes, text and fonts, touch points, buttons on screen, a WiFi clock, and a space mission panel.
0 of 7 done
7 lessons in 4 chapters, about 5 hours on a simulated Cheap Yellow Display (ESP32-2432S028R). Free, in your browser, every step checked by the simulator.
A night launch in pixels: coordinates where y grows down, lines, rectangles, circles and triangles, colors as RGB565 numbers, and a satellite animated by erasing and redrawing.
Open it in the simulatorWhere did the finger land? Read the XPT2046 touch chip, see its raw numbers, map them to pixels, draw a crosshair, and find out what calibration is by getting it wrong.
Open it in the simulatorJoin WiFi, ask a time server for the time with NTP, add a time zone, and show it in seven-segment digits. The network is simulated, and the lesson says exactly what that means.
Open it in the simulatorEach lesson opens when the one before it is done, and each chapter ends in a project.
The board, then shapes, colors and animation.
Meet the Cheap Yellow Display: an ESP32 glued to a touch screen. Where the screen, the touch film, the RGB LED and the free pins are wired, and a first hello on the screen.
0 of 6 steps
A night launch in pixels: coordinates where y grows down, lines, rectangles, circles and triangles, colors as RGB565 numbers, and a satellite animated by erasing and redrawing.
0 of 6 steps
Fonts and text, and where a finger lands.
Words and numbers on the screen: TFT_eSPI’s numbered fonts measured in pixels, the text datum that anchors a string, scaling, and a score that counts up without flicker.
0 of 6 steps
Where did the finger land? Read the XPT2046 touch chip, see its raw numbers, map them to pixels, draw a crosshair, and find out what calibration is by getting it wrong.
0 of 6 steps
Buttons that do things, and a clock that asks the internet.
Turn rectangles into buttons: a struct for each one, a hit test, a pressed look, and an action. Three buttons that light the board’s RGB LED red, green or blue.
0 of 6 steps
Join WiFi, ask a time server for the time with NTP, add a time zone, and show it in seven-segment digits. The network is simulated, and the lesson says exactly what that means.
0 of 6 steps
A touch remote: a space mission panel.
A touch remote for a rocket: ARM, LAUNCH and ABORT buttons drive a safe, armed, countdown and liftoff state machine, light the LED, and send every command over serial.
0 of 8 steps
All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.
Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.
Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kitYes. All 7 lessons of Touch apps on the Cheap Yellow Display are free and run in your browser, with nothing to install and no parts to buy before you start.
No. Every lesson runs on a simulated Cheap Yellow Display (ESP32-2432S028R) with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.
About 5 hours: 7 lessons in 4 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.
Each chapter ends in a project that puts it together: Drawing shapes, Touch points and A WiFi clock.
With "The board tour", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.