All paths

Brushless motors and ESCs

How a brushless motor spins and how fast, the pulse an ESC reads, arming and calibration, throttle curves, a kill switch and LiPo safety, and a thrust stand with a load cell and a current sensor.

Arduino Uno R3Free7 lessons6 h4 chapters2,477 XPRobotics · Advanced+250 XP

0 of 7 done

What you will build

3 projects, built step by step

7 lessons in 4 chapters, about 6 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.

Chapter 1 project

Kv, volts and props

The thrust stand: set throttle by percent, predict the no-load rpm from Kv x volts x throttle, read what the pack sags to, and fix a sketch whose motor model no longer matches the motor.

Open it in the simulator
Chapter 2 project

Arming and calibration

What an ESC does from power-up: start-up tones, waiting for low throttle, arming. Then lose the signal on purpose, meet an ESC whose endpoints are not the sketch’s, and calibrate the sketch to match.

Open it in the simulator
Chapter 3 project

Safety: kill switch and LiPo

A kill button that cuts and disarms, a low-voltage cutoff that protects the pack, and what a LiPo’s cell voltage says: full, storage, in use or empty. Props off for every test.

Open it in the simulator
The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

Inside a brushless motor

Commutation, Kv times volts, packs and motors, and a sketch whose model has to match.

  1. Open250 XP

    How a brushless motor spins

    An A2212 outrunner on a 30 A ESC and a 3S LiPo, from the gallery. Arm it, open the throttle with a stick, and predict its speed from Kv and the pack’s volts, then change the pack and the motor.

    0 of 5 steps

  2. ProjectLocked500 XP

    Kv, volts and props

    The thrust stand: set throttle by percent, predict the no-load rpm from Kv x volts x throttle, read what the pack sags to, and fix a sketch whose motor model no longer matches the motor.

    0 of 5 steps

4 questions, graded as you go.
Chapter 2

Talking to an ESC

The servo-style pulse, two locks before a motor spins, signal loss and endpoint calibration.

  1. Locked250 XP

    ESC signals

    An ESC reads the same pulse a servo does: 1000 to 2000 microseconds, 50 times a second. Count the pulses, find the sketch’s software arm, and work out every width from a percentage.

    0 of 5 steps

  2. ProjectLocked424 XP

    Arming and calibration

    What an ESC does from power-up: start-up tones, waiting for low throttle, arming. Then lose the signal on purpose, meet an ESC whose endpoints are not the sketch’s, and calibrate the sketch to match.

    0 of 4 steps

4 questions, graded as you go.
Chapter 3

Control and safety

Ramps and expo curves, a kill button, a low-voltage cutoff and what a LiPo’s voltage means.

  1. Locked212 XP

    Throttle curves and ramps

    A ramp that limits how fast the throttle moves, the motor’s own lag, and an expo curve that gives fine control at the bottom of the stick. Predict each pulse and change the curve.

    0 of 4 steps

  2. ProjectLocked576 XP

    Safety: kill switch and LiPo

    A kill button that cuts and disarms, a low-voltage cutoff that protects the pack, and what a LiPo’s cell voltage says: full, storage, in use or empty. Props off for every test.

    0 of 6 steps

5 questions, graded as you go.
Chapter 4

Boss build

A calibrated thrust stand: the hover point, grams per watt and a full throttle sweep.

  1. Locked265 XP

    Boss: a thrust stand

    Tare and calibrate the load cell with a known weight, measure the hover point in grams, amps and grams per watt, then sweep the throttle and record a thrust curve, the way motor makers test.

    0 of 6 steps

3 questions, graded as you go.
Syllabus

Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

Inside a brushless motor

  1. How a brushless motor spinsAn A2212 outrunner on a 30 A ESC and a 3S LiPo, from the gallery. Arm it, open the throttle with a stick, and predict its speed from Kv and the pack’s volts, then change the pack and the motor.
  2. Kv, volts and propsThe thrust stand: set throttle by percent, predict the no-load rpm from Kv x volts x throttle, read what the pack sags to, and fix a sketch whose motor model no longer matches the motor.
Chapter 2

Talking to an ESC

  1. ESC signalsAn ESC reads the same pulse a servo does: 1000 to 2000 microseconds, 50 times a second. Count the pulses, find the sketch’s software arm, and work out every width from a percentage.
  2. Arming and calibrationWhat an ESC does from power-up: start-up tones, waiting for low throttle, arming. Then lose the signal on purpose, meet an ESC whose endpoints are not the sketch’s, and calibrate the sketch to match.
Chapter 3

Control and safety

  1. Throttle curves and rampsA ramp that limits how fast the throttle moves, the motor’s own lag, and an expo curve that gives fine control at the bottom of the stick. Predict each pulse and change the curve.
  2. Safety: kill switch and LiPoA kill button that cuts and disarms, a low-voltage cutoff that protects the pack, and what a LiPo’s cell voltage says: full, storage, in use or empty. Props off for every test.
Chapter 4

Boss build

  1. Boss: a thrust standTare and calibrate the load cell with a known weight, measure the hover point in grams, amps and grams per watt, then sweep the throttle and record a thrust curve, the way motor makers test.
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Brushless motors and ESCs

Is Brushless motors and ESCs free?

Yes. All 7 lessons of Brushless motors and ESCs are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Arduino Uno R3?

No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Brushless motors and ESCs take?

About 6 hours: 7 lessons in 4 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: Kv, volts and props, Arming and calibration and Safety: kill switch and LiPo.

Where do I start?

With "How a brushless motor spins", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.