Source: https://mokxi.com/teachers/plans/spice-simulation
Updated: 2026-11-19

Lesson plan

# SPICE simulation lesson plan

What a circuit simulator really does, on the SPICE engine Mokxi runs underneath: netlists, the operating point, transient and AC analysis, sweeps, models from datasheets, and a preamp verified before it is built.

7 chapters, 7 lessons, about 6 hours, no board. Every lesson runs in the browser, with nothing to install.

Start a class from this course

The unit

## Objectives and materials

### By the end, students can

- A circuit as text: nodes, ground and one line per part.
- Every node at DC, and where power-on differs from .op.
- The circuit in time, read in multiples of tau.
- A Bode plot proved point by point.
- 60 mV a decade and a Zener's knee.
- hFE, Vce(sat), GBW and the .model card.
- Predict, verify and change a preamp before you build it.

### Materials for the whole unit

- Capacitor
- DC voltage source x 3
- Function generator
- Multimeter x 3
- Op-amp
- Oscilloscope
- Resistor x 6
- Transistor (NPN or PNP) x 2
- Zener diode

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 1 h

## Netlists

A circuit as text: nodes, ground and one line per part.

Lesson | Time | What students do

Netlists: a circuit as text Read and write the text every SPICE engine runs: nodes, ground as node 0, one line per part, SPICE's 0 V ammeter, and the same divider as a canvas and as a deck. | 60 min

- Run it: the canvas is a deck
- Edit a line
- Add a line, add a part
- Solve the new deck
- SPICE's ammeter
- Run the deck itself

### Materials

- DC voltage source
- Multimeter x 2
- Resistor x 3

### Check for understanding

Each student finishes "Netlists: a circuit as text" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Run the deck itself".

Chapter 2. About 50 min

## Operating point

Every node at DC, and where power-on differs from .op.

Lesson | Time | What students do

The operating point What .op solves: every node voltage of a transistor stage at once, how a bias change moves it, Mokxi's Shift+O readout, and the one place power-on and SPICE's .op disagree. | 50 min

- Run it: the base node
- The emitter node
- The collector node
- Move the point
- Where power-on and .op differ

### Materials

- Capacitor
- DC voltage source x 2
- Multimeter x 3
- Resistor x 5
- Transistor (NPN or PNP)

### Check for understanding

Each student finishes "The operating point" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Where power-on and .op differ".

Chapter 3. About 1 h

## Transient

The circuit in time, read in multiples of tau.

Lesson | Time | What students do

Transient analysis The circuit stepped through time: an RC fed a square wave, the time constant against the half period, what one tau, two and five look like, and the same run written as a .tran deck. | 60 min

- Run it: too fast to charge
- One tau per half cycle
- Five tau: all the way
- Change R instead
- Change C
- Write the .tran

### Materials

- Capacitor
- Function generator
- Oscilloscope
- Resistor

### Check for understanding

Each student finishes "Transient analysis" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Write the .tran".

Chapter 4. About 50 min

## AC sweep

A Bode plot proved point by point.

Lesson | Time | What students do

AC sweep What an .ac analysis computes and how a scope proves it point by point: an RC low-pass a decade above its corner, at the corner, below it, a moved corner, and the Bode plot in the Analysis sheet. | 50 min

- Run it: a decade above the corner
- At the corner
- In the passband
- Move the corner
- The whole plot at once

### Materials

- Capacitor
- Function generator
- Oscilloscope
- Resistor

### Check for understanding

Each student finishes "AC sweep" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "The whole plot at once".

Chapter 5. About 50 min

## Parameter sweeps

60 mV a decade and a Zener's knee.

Lesson | Time | What students do

Parameter sweeps Step one value and watch another: a transistor's current against its base voltage, 60 mV per decade, a Zener found by sweeping its supply, and the Analysis sheet's DC and parameter sweep. | 50 min

- Run it: the first point
- Sixty millivolts
- Another decade
- Sweep a supply: below the knee
- Above the knee

### Materials

- DC voltage source x 3
- Multimeter
- Resistor x 2
- Transistor (NPN or PNP)
- Zener diode

### Check for understanding

Each student finishes "Parameter sweeps" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Above the knee".

Chapter 6. About 50 min

## Models from datasheets

hFE, Vce(sat), GBW and the .model card.

Lesson | Time | What students do

Models from datasheets Turn datasheet numbers into model parameters: hFE into beta, Vce(sat) at its test condition, an op-amp's gain-bandwidth product checked at its own bandwidth, and the .model card behind it all. | 50 min

- Run it: the card as shipped
- hFE from the datasheet
- Vce(sat) at its test point
- Gain-bandwidth product
- The .model card

### Materials

- DC voltage source x 2
- Function generator
- Multimeter
- Op-amp
- Oscilloscope
- Resistor x 6
- Transistor (NPN or PNP) x 2

### Check for understanding

Each student finishes "Models from datasheets" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "The .model card".

Chapter 7. About 50 min

## Boss build

Predict, verify and change a preamp before you build it.

Lesson | Time | What students do

Boss: verify before you build Design a microphone preamp on paper, predict its operating point and gain, verify every number in the simulator, then change the design to a new spec and verify again before a single part is bought. | 50 min

- Predict on paper
- Verify the operating point
- Verify the follower
- Verify the gain
- New spec: twice the gain

### Materials

- Capacitor
- DC voltage source
- Function generator
- Multimeter x 2
- Op-amp
- Oscilloscope
- Resistor x 5
- Transistor (NPN or PNP)

### Check for understanding

Each student finishes "Boss: verify before you build" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "New spec: twice the gain".

Your class

## Teach this unit as a class

Start a class from this course and its 7 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.

Start a class from this course See the demo class

More units

## Other lesson plans

Electronics basics 20 lessons, about 10 h. Embedded on the Arduino Uno 16 lessons, about 12 h. Embedded on the ESP32-C3 13 lessons, about 11 h. Embedded on the Raspberry Pi Pico 7 lessons, about 6 h. Build your own fight stick 5 lessons, about 4 h. Embedded on the STM32F411 6 lessons, about 6 h. C++ on a board 13 lessons, about 10 h. Digital logic and memory 4 lessons, about 4 h. Interactive devices on the Uno 9 lessons, about 8 h. From gates to a computer 23 lessons, about 16 h. Build a claw machine 8 lessons, about 6 h. Every unit All the courses as ready-made units, on the teachers page.
