Source: https://mokxi.com/teachers/plans/protection-circuits
Updated: 2026-11-19

Lesson plan

# Protection circuits lesson plan

Keep a mistake from killing your electronics: fuses and resettable limits, reverse polarity, surge clamps, inrush limiting, flyback clamps, crowbars, and a power input you harden against all of it.

7 chapters, 7 lessons, about 5 hours, no board. Every lesson runs in the browser, with nothing to install.

Start a class from this course

The unit

## Objectives and materials

### By the end, students can

- One-shot fuses against resettable limits.
- A series diode and a P-MOSFET.
- Clamp a surge, and what ESD needs.
- A limiter, its cost, and the bypass.
- A diode clamp and a diode-Zener clamp.
- Sense, short, and let the fuse clear it.
- A bulletproof 12 V input.

### Materials for the whole unit

- Bench power supply
- Capacitor
- DC voltage source x 2
- Diode x 2
- Filament lamp x 2
- MOSFET
- Multimeter x 3
- Oscilloscope
- Resistor x 3
- Slide switch x 2
- Solenoid
- Zener diode

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 45 min

## Fuses and PTCs

One-shot fuses against resettable limits.

Lesson | Time | What students do

Fuses and resettable limits A one-shot fuse against a resettable limit: a 2 A fuse that opens on a short and stays open, a current limit that holds a short at a safe current, the rail it collapses, and the recovery a PTC or eFuse gives you. | 45 min

- Run it: a protected lamp
- A short: one shot
- A resettable limit
- The rail collapses
- Which one when

### Materials

- Bench power supply
- Filament lamp
- Multimeter
- Slide switch

### Check for understanding

Each student finishes "Fuses and resettable limits" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Which one when".

Chapter 2. About 45 min

## Reverse polarity

A series diode and a P-MOSFET.

Lesson | Time | What students do

Reverse polarity Two ways to survive a battery put in backward: a series Schottky diode and what it costs in volts, and a P-channel MOSFET that does the same with almost no loss, blocking either way around. | 45 min

- Run it: a series diode
- Plug it in backward
- What the diode costs
- The MOSFET way
- Backward again

### Materials

- DC voltage source
- Diode
- Filament lamp x 2
- MOSFET
- Multimeter x 2
- Resistor x 2

### Check for understanding

Each student finishes "Reverse polarity" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Backward again".

Chapter 3. About 50 min

## TVS and ESD

Clamp a surge, and what ESD needs.

Lesson | Time | What students do

TVS and ESD A surge on a supply line burns out an unprotected lamp; a clamp diode across the rail holds it at a safe voltage and takes the current instead; and what ESD is, and why it needs a faster part than the simulator models. | 50 min

- Run it: the normal rail
- A surge
- Clamp the rail
- Where the energy goes
- Resistance helps
- ESD, the fast one

### Materials

- DC voltage source x 2
- Filament lamp
- Multimeter
- Resistor
- Slide switch
- Zener diode

### Check for understanding

Each student finishes "TVS and ESD" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "ESD, the fast one".

Chapter 4. About 45 min

## Inrush limiting

A limiter, its cost, and the bypass.

Lesson | Time | What students do

Inrush limiting A big input capacitor that blows the fuse at switch-on, a limiter resistor (an NTC's cold resistance) that stops it, the power the limiter wastes once running, and the bypass that takes it out of the circuit. | 45 min

- Run it: limited
- No limiter
- Size the limiter
- What the limiter costs
- Bypass it

### Materials

- Capacitor
- DC voltage source
- Multimeter x 2
- Resistor x 3
- Slide switch

### Check for understanding

Each student finishes "Inrush limiting" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Bypass it".

Chapter 5. About 35 min

## Flyback diodes

A diode clamp and a diode-Zener clamp.

Lesson | Time | What students do

Flyback clamps The coil kick from the magnetism course, clamped two ways: a plain flyback diode that holds the drain one drop above the supply, and a diode-Zener clamp that lets it rise to a set voltage to dump the energy faster. | 35 min

- Run it: the plain diode
- The current it carries
- A diode-Zener clamp
- The Zener takes it

### Materials

- DC voltage source
- Diode x 2
- MOSFET
- Oscilloscope
- Resistor
- Slide switch x 2
- Solenoid
- Zener diode

### Check for understanding

Each student finishes "Flyback clamps" on their own, without opening the hints. The simulator checks 4 of its 4 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "The Zener takes it".

Chapter 6. About 45 min

## Crowbars

Sense, short, and let the fuse clear it.

Lesson | Time | What students do

Crowbars An overvoltage crowbar: a Zener that senses the rail, a switch that shorts it, and the fuse that clears the fault, then the same crowbar on a current-limited supply, and how the trip point is chosen. | 45 min

- Run it: normal
- Just under the trip point
- Overvoltage: fire
- On a limited supply
- Choose the trip point

### Materials

- Bench power supply
- Filament lamp
- MOSFET
- Multimeter
- Resistor
- Zener diode

### Check for understanding

Each student finishes "Crowbars" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Choose the trip point".

Chapter 7. About 45 min

## Boss build

A bulletproof 12 V input.

Lesson | Time | What students do

Boss: a bulletproof power input One 12 V input hardened against everything in the course: a fuse, a P-MOSFET for reverse polarity and a clamp for surges in front of a lamp, then test it backward, surged and shorted, and retune the clamp for 16 V parts. | 45 min

- Run it: normal power
- Backward
- Surged
- Shorted
- Make it yours: 16 V parts

### Materials

- DC voltage source x 2
- Filament lamp
- MOSFET
- Multimeter x 3
- Resistor x 2
- Slide switch x 2
- Zener diode

### Check for understanding

Each student finishes "Boss: a bulletproof power input" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Make it yours: 16 V parts".

Your class

## Teach this unit as a class

Start a class from this course and its 7 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.

Start a class from this course See the demo class

More units

## Other lesson plans

Electronics basics 20 lessons, about 10 h. Embedded on the Arduino Uno 16 lessons, about 12 h. Embedded on the ESP32-C3 13 lessons, about 11 h. Embedded on the Raspberry Pi Pico 7 lessons, about 6 h. Build your own fight stick 5 lessons, about 4 h. Embedded on the STM32F411 6 lessons, about 6 h. C++ on a board 13 lessons, about 10 h. Digital logic and memory 4 lessons, about 4 h. Interactive devices on the Uno 9 lessons, about 8 h. From gates to a computer 23 lessons, about 16 h. Build a claw machine 8 lessons, about 6 h. Every unit All the courses as ready-made units, on the teachers page.
