Source: https://mokxi.com/teachers/plans/oscillators-and-timing-circuits
Updated: 2026-11-19

Lesson plan

# Oscillators and timing circuits lesson plan

The 555 in depth, the monostable, Schmitt and CD4060 oscillators, RC phase shift and Wien bridge sines, ending in a tone generator tuned to concert A.

7 chapters, 7 lessons, about 6 hours, no board. Every lesson runs in the browser, with nothing to install.

Start a class from this course

The unit

## Objectives and materials

### By the end, students can

- Frequency, duty, the 50 percent floor and the diode that breaks it.
- One pulse per trigger: T = 1.1 RC.
- One gate, one resistor, one capacitor.
- An RC oscillator and fourteen halvings.
- Three stages, 180 degrees and a gain of 29.
- A gain of 3 on one supply.
- A divided 555 tuned to 440 Hz.

### Materials for the whole unit

- 74HC14 Schmitt inverter
- Bench power supply
- Capacitor x 4
- CD4060 counter with oscillator
- Diode x 2
- Frequency counter x 3
- LED
- LM358 dual op-amp
- Multimeter
- NE555 timer
- Oscilloscope
- Piezo speaker
- Pushbutton
- Resistor x 7
- Slide switch

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 1 h 5 min

## 555 astable deep

Frequency, duty, the 50 percent floor and the diode that breaks it.

Lesson | Time | What students do

555 astable, in depth A 555 runs free at 68.6 Hz: the frequency and duty formulas, the capacitor between a third and two thirds of the supply, a tenth of the capacitor, a predicted resistor, a diode that breaks the 50 percent floor, and a slow blink. | 65 min

- Run it: 68.6 Hz
- The duty cycle
- A tenth of the capacitor
- Predict: R2 of 4.7k
- Under 50 percent with a diode
- Predict: a slow blink

### Materials

- Bench power supply
- Capacitor x 2
- Diode
- Frequency counter
- Multimeter
- NE555 timer
- Oscilloscope
- Resistor x 2
- Slide switch

### Check for understanding

Each student finishes "555 astable, in depth" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Predict: a slow blink".

Chapter 2. About 45 min

## Monostable

One pulse per trigger: T = 1.1 RC.

Lesson | Time | What students do

Monostable: one pulse per trigger A 555 monostable makes one pulse of about 1.1 s per press of a button: T = 1.1 RC, a smaller capacitor for a shorter pulse, a predicted long pulse, and why monostables clean up switches and stretch short events. | 45 min

- Run it and press
- Then it times out
- A shorter pulse
- Predict: a long pulse

### Materials

- Bench power supply
- Capacitor
- LED
- NE555 timer
- Oscilloscope
- Pushbutton
- Resistor x 3

### Check for understanding

Each student finishes "Monostable: one pulse per trigger" on their own, without opening the hints. The simulator checks 4 of its 4 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Predict: a long pulse".

Chapter 3. About 45 min

## Schmitt oscillators

One gate, one resistor, one capacitor.

Lesson | Time | What students do

Schmitt oscillators: one gate, one R, one C A 74HC14 inverter with hysteresis and an RC around it oscillates on its own: the frequency, an uneven duty from uneven thresholds, double the capacitor, a predicted resistor, and a second gate as a buffer. | 45 min

- Run it: a gate that oscillates
- Uneven thresholds, uneven duty
- Twice the capacitor
- The buffer

### Materials

- 74HC14 Schmitt inverter
- Bench power supply
- Capacitor
- Frequency counter x 2
- Multimeter
- Oscilloscope
- Resistor

### Check for understanding

Each student finishes "Schmitt oscillators: one gate, one R, one C" on their own, without opening the hints. The simulator checks 4 of its 4 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "The buffer".

Chapter 4. About 55 min

## CD4060 dividers

An RC oscillator and fourteen halvings.

Lesson | Time | What students do

CD4060 dividers: slow and steady from fast A CD4060's RC oscillator at 4.5 kHz and its binary dividers: Q4 at a sixteenth, Q7 at a 128th, a predicted capacitor, and how a one-minute timer comes out of fourteen flip-flops. | 55 min

- Run it: the oscillator
- Q4: a sixteenth
- Q7: a 128th
- Predict: 22 nF
- A one-minute timer

### Materials

- Bench power supply
- Capacitor
- CD4060 counter with oscillator
- Frequency counter x 3
- Resistor x 2

### Check for understanding

Each student finishes "CD4060 dividers: slow and steady from fast" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A one-minute timer".

Chapter 5. About 45 min

## RC phase shift

Three stages, 180 degrees and a gain of 29.

Lesson | Time | What students do

RC phase shift: three stages and a gain of 29 An LM358 inverting amplifier fed back through three RC stages: 650 Hz from the formula, the size of the wave, twice the capacitors, and a predicted retune. | 45 min

- Run it: about 650 Hz
- How big
- Twice the capacitors
- Predict: 4.7 nF

### Materials

- Bench power supply
- Capacitor x 3
- Frequency counter
- LM358 dual op-amp
- Multimeter
- Oscilloscope
- Resistor x 6

### Check for understanding

Each student finishes "RC phase shift: three stages and a gain of 29" on their own, without opening the hints. The simulator checks 4 of its 4 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Predict: 4.7 nF".

Chapter 6. About 45 min

## Wien bridge

A gain of 3 on one supply.

Lesson | Time | What students do

Wien bridge on one supply The Wien bridge from the op-amp cookbook, rebuilt on an LM358 from one 9 V supply: a 4.5 V bias, 1592 Hz from 1 / (2 pi RC), the sine's size, both capacitors retuned together, and a predicted resistor pair. | 45 min

- Run it: 1592 Hz
- A sine that holds its size
- Both capacitors together
- Predict: 20k resistors

### Materials

- Bench power supply
- Capacitor x 4
- Diode x 2
- Frequency counter
- LM358 dual op-amp
- Multimeter
- Oscilloscope
- Resistor x 7

### Check for understanding

Each student finishes "Wien bridge on one supply" on their own, without opening the hints. The simulator checks 4 of its 4 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Predict: 20k resistors".

Chapter 7. About 1 h 5 min

## Boss build

A divided 555 tuned to 440 Hz.

Lesson | Time | What students do

Boss: a steady tone generator A 555 at about 7 kHz clocks a CD4060 that divides it by 16 into an LM358 buffer and a piezo: wire the clock, read both counters, tune the 555 to concert A at 440 Hz, then drop it an octave. | 65 min

- Wire the clock
- Run it: the clock
- Divided by 16
- The piezo sings
- Your change: tune it to A440
- Your change: an octave down

### Materials

- Bench power supply
- Capacitor x 2
- CD4060 counter with oscillator
- Frequency counter x 2
- LM358 dual op-amp
- NE555 timer
- Oscilloscope
- Piezo speaker
- Resistor x 2

### Check for understanding

Each student finishes "Boss: a steady tone generator" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Your change: an octave down".

Your class

## Teach this unit as a class

Start a class from this course and its 7 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.

Start a class from this course See the demo class

More units

## Other lesson plans

Electronics basics 20 lessons, about 10 h. Embedded on the Arduino Uno 16 lessons, about 12 h. Embedded on the ESP32-C3 13 lessons, about 11 h. Embedded on the Raspberry Pi Pico 7 lessons, about 6 h. Build your own fight stick 5 lessons, about 4 h. Embedded on the STM32F411 6 lessons, about 6 h. C++ on a board 13 lessons, about 10 h. Digital logic and memory 4 lessons, about 4 h. Interactive devices on the Uno 9 lessons, about 8 h. From gates to a computer 23 lessons, about 16 h. Build a claw machine 8 lessons, about 6 h. Every unit All the courses as ready-made units, on the teachers page.
