Source: https://mokxi.com/teachers/plans/linear-power-supplies
Updated: 2026-11-19

Lesson plan

# Linear power supplies lesson plan

From a transformer's AC to clean DC: bridge rectifiers and ripple, Zener regulators, the LM317, low-dropout regulators, heat and heatsinks, and a dual bench supply you design down to every part.

7 chapters, 7 lessons, about 5 hours, no board. Every lesson runs in the browser, with nothing to install.

Start a class from this course

The unit

## Objectives and materials

### By the end, students can

- A secondary, a bridge and a smoothing capacitor.
- I / (2 f C), on an AC range and a scope.
- A resistor, a Zener, and the load they can carry.
- Two resistors set the voltage; headroom keeps it.
- How low the input can go.
- Watts, degrees per watt, and cutting the heat.
- A dual bench supply.

### Materials for the whole unit

- Capacitor x 3
- DC voltage source
- Diode x 4
- LM317 regulator
- Mains transformer, 230 V or 120 V to 12 V
- Multimeter x 3
- Oscilloscope
- Resistor x 6
- Signal generator
- Voltage regulator
- Zener diode

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 40 min

## Transformer to DC

A secondary, a bridge and a smoothing capacitor.

Lesson | Time | What students do

Transformer to DC From the wall to a DC rail: a transformer's 12 V secondary, a bridge rectifier that flips every half cycle the same way, the two diode drops it costs, and the smoothing capacitor that turns humps into a rail. | 40 min

- Run it: the secondary
- A bridge: every half the same way
- Smooth it
- The diodes' share
- A light load

### Materials

- Capacitor
- Diode x 4
- Mains transformer, 230 V or 120 V to 12 V
- Multimeter
- Resistor x 2
- Signal generator

### Check for understanding

Each student finishes "Transformer to DC" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A light load".

Chapter 2. About 40 min

## Ripple

I / (2 f C), on an AC range and a scope.

Lesson | Time | What students do

Ripple The sawtooth a reservoir capacitor leaves on the rail: reading it on an AC range, the I / (2 f C) rule, a bigger capacitor, a heavier load, and why the lowest point of the ripple is the number that matters. | 40 min

- Run it: a 12 V adapter
- Read the ripple
- A bigger capacitor
- A heavier load
- A light load

### Materials

- Capacitor
- Diode x 4
- Multimeter x 2
- Oscilloscope
- Resistor
- Signal generator

### Check for understanding

Each student finishes "Ripple" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A light load".

Chapter 3. About 40 min

## Zener regulators

A resistor, a Zener, and the load they can carry.

Lesson | Time | What students do

Zener regulators The simplest regulator: a resistor and a Zener on the raw rail, how well it holds 5 V as the load changes, the current it wastes, and the load it cannot carry. | 40 min

- Run it: 5 V from 15
- The current it wastes
- Load it
- Past its limit
- Resize the resistor

### Materials

- Capacitor
- Diode x 4
- Multimeter x 2
- Resistor x 2
- Signal generator
- Zener diode

### Check for understanding

Each student finishes "Zener regulators" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Resize the resistor".

Chapter 4. About 40 min

## LM317

Two resistors set the voltage; headroom keeps it.

Lesson | Time | What students do

The LM317 An adjustable regulator from three legs and two resistors: 5 V from 240 and 720 ohms, a new voltage from a new resistor, how little ripple gets through, and the headroom it needs. | 40 min

- Run it: 5 V
- Set 9 V
- Ripple rejection
- Headroom
- Down to 3.3 V

### Materials

- Capacitor x 2
- Diode x 4
- LM317 regulator
- Multimeter x 2
- Resistor x 3
- Signal generator

### Check for understanding

Each student finishes "The LM317" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Down to 3.3 V".

Chapter 5. About 40 min

## LDO dropout

How low the input can go.

Lesson | Time | What students do

LDO dropout How close to its output a regulator's input can fall: a 7805 that gives up 2 V short, an AMS1117 that needs 1.1 V, and an MCP1700 that runs a 3.3 V board from a single lithium cell to the end. | 40 min

- Run it: plenty of headroom
- The battery sags
- A lower dropout
- One cell to the end
- Even an LDO runs out

### Materials

- Capacitor
- DC voltage source
- Multimeter
- Resistor
- Voltage regulator

### Check for understanding

Each student finishes "LDO dropout" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Even an LDO runs out".

Chapter 6. About 40 min

## Heatsinks

Watts, degrees per watt, and cutting the heat.

Lesson | Time | What students do

Heatsinks A linear regulator turns the voltage it drops into heat: measure it, work out the junction temperature from the datasheet's degrees per watt, see what a heatsink buys, and cut the heat at the source. | 40 min

- Run it: half an amp
- Where 3.5 W goes
- Degrees per watt
- Cut it at the source
- Too far

### Materials

- Capacitor
- DC voltage source
- Multimeter x 3
- Resistor
- Voltage regulator

### Check for understanding

Each student finishes "Heatsinks" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Too far".

Chapter 7. About 50 min

## Boss build

A dual bench supply.

Lesson | Time | What students do

Boss: a bench supply A small dual bench supply from the course's parts: a 24 V transformer, a bridge and a reservoir, an adjustable LM317 output, and a fixed 5 V output fed through a Zener pre-regulator. Set it, load it, check its ripple and headroom, and give it the voltage you need. | 50 min

- Run it: the raw rail
- The adjustable output
- The fixed 5 V
- Find the fixed output's limit
- Set it to 24 V
- Make it yours

### Materials

- Capacitor x 3
- Diode x 4
- LM317 regulator
- Mains transformer, 230 V or 120 V to 12 V
- Multimeter x 3
- Resistor x 6
- Signal generator
- Voltage regulator
- Zener diode

### Check for understanding

Each student finishes "Boss: a bench supply" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Make it yours".

Your class

## Teach this unit as a class

Start a class from this course and its 7 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.

Start a class from this course See the demo class

More units

## Other lesson plans

Electronics basics 20 lessons, about 10 h. Embedded on the Arduino Uno 16 lessons, about 12 h. Embedded on the ESP32-C3 13 lessons, about 11 h. Embedded on the Raspberry Pi Pico 7 lessons, about 6 h. Build your own fight stick 5 lessons, about 4 h. Embedded on the STM32F411 6 lessons, about 6 h. C++ on a board 13 lessons, about 10 h. Digital logic and memory 4 lessons, about 4 h. Interactive devices on the Uno 9 lessons, about 8 h. From gates to a computer 23 lessons, about 16 h. Build a claw machine 8 lessons, about 6 h. Every unit All the courses as ready-made units, on the teachers page.
