Source: https://mokxi.com/teachers/plans/know-your-components
Updated: 2026-11-19

Lesson plan

# Know your components lesson plan

Pick up any part and know what it is: resistor bands, capacitor codes, diodes and LEDs, transistor packages, pin 1 on a chip, SMD markings, and a mixed parts bin sorted into a working blinker.

7 chapters, 7 lessons, about 5 hours, no board. Every lesson runs in the browser, with nothing to install.

Start a class from this course

The unit

## Objectives and materials

### By the end, students can

- Four bands, five bands, gold multipliers and the E12 series.
- uF, nF and pF, the three-digit code, tolerance letters and electrolytics.
- Stripes, long legs, forward volts and the LED's resistor.
- TO-92 and TO-220, mirror pinouts, NPN, PNP and MOSFETs.
- The notch and the dot, counting pins, and a datasheet for every chip.
- SMD codes, Zener numbers and diodes in mixed bags.
- Sort a bin, fix a blinker, make it yours.

### Materials for the whole unit

- Capacitor x 4
- Component tester x 5
- DC voltage source x 2
- Diode x 2
- LED x 2
- LM358 dual op-amp
- MOSFET
- Multimeter
- NE555 timer
- Resistor x 8
- Slide switch
- Transistor (NPN or PNP) x 3
- Zener diode

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 40 min

## Resistor color codes

Four bands, five bands, gold multipliers and the E12 series.

Lesson | Time | What students do

Resistor color codes Read four-band and five-band resistors, the gold and silver multipliers, the tolerance band, and pick a real value for an LED, with a component tester checking every answer. | 40 min

- Run it: three testers
- Two digits and a multiplier
- Small values: a brown multiplier
- Gold in the third band
- Five bands: three digits
- Pick a real value

### Materials

- Component tester x 3
- DC voltage source
- LED
- Resistor x 4

### Check for understanding

Each student finishes "Resistor color codes" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Pick a real value".

Chapter 2. About 35 min

## Capacitor codes

uF, nF and pF, the three-digit code, tolerance letters and electrolytics.

Lesson | Time | What students do

Capacitor codes Microfarads, nanofarads and picofarads, the three-digit code on ceramic caps, tolerance letters, electrolytic labels, and what to do when a part is too small for the tester. | 35 min

- Run it: 1 uF in a tester
- The three-digit code
- Electrolytics say it plainly
- Too small for the tester
- Tolerance letters

### Materials

- Capacitor x 4
- Component tester x 3
- Multimeter

### Check for understanding

Each student finishes "Capacitor codes" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Tolerance letters".

Chapter 3. About 40 min

## Diodes and LEDs

Stripes, long legs, forward volts and the LED's resistor.

Lesson | Time | What students do

Diodes and LEDs Find the cathode by its stripe and an LED by its short leg, read forward voltage on a tester, tell silicon from Schottky, see why LED colors drop different volts, and set an LED's current. | 40 min

- Run it: a diode in a tester
- Silicon or Schottky
- The stripe goes toward ground
- Long leg, short leg
- Colors drop different volts
- Set the LED current

### Materials

- Component tester x 2
- DC voltage source x 2
- Diode x 2
- LED x 2
- Resistor x 2

### Check for understanding

Each student finishes "Diodes and LEDs" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Set the LED current".

Chapter 4. About 40 min

## Transistor packages

TO-92 and TO-220, mirror pinouts, NPN, PNP and MOSFETs.

Lesson | Time | What students do

Transistor packages TO-92 and TO-220, why the same shape hides different pinouts, NPN against PNP, a MOSFET in a transistor's clothes, and a transistor switching an LED. | 40 min

- Run it: hFE from a tester
- Same shape, different legs
- NPN or PNP
- A MOSFET in disguise
- Switch it on
- The load sets the current

### Materials

- Component tester x 3
- DC voltage source
- LED
- MOSFET
- Resistor x 2
- Slide switch
- Transistor (NPN or PNP) x 3

### Check for understanding

Each student finishes "Transistor packages" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "The load sets the current".

Chapter 5. About 50 min

## ICs and pin 1

The notch and the dot, counting pins, and a datasheet for every chip.

Lesson | Time | What students do

ICs and pin 1 Find pin 1 by the notch and the dot, count around a DIP, power a 555 by its pin numbers, change its rate with a capacitor code, and learn why every chip needs its own datasheet. | 50 min

- Pin 1 is ground on a 555
- Pin 8 across from it
- Pin 4 must not float
- Run it: pin 3 blinks
- A code sets the rate
- Same package, different pins
- The comparator lights

### Materials

- Capacitor
- DC voltage source
- LED x 2
- LM358 dual op-amp
- NE555 timer
- Resistor x 8

### Check for understanding

Each student finishes "ICs and pin 1" on their own, without opening the hints. The simulator checks 7 of its 7 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "The comparator lights".

Chapter 6. About 50 min

## Part markings

SMD codes, Zener numbers and diodes in mixed bags.

Lesson | Time | What students do

Part markings Surface-mount resistor codes (103, 4R7, 4701), Zener part numbers that state their voltage, glass and black diodes by number, and how to read what little a tiny part says. | 50 min

- Run it: an SMD resistor
- R is the decimal point
- Four digits for 1 percent
- A Zener says its voltage
- Swap by part number
- Give it its test current
- Glass or black: read the number

### Materials

- Component tester x 4
- DC voltage source
- Diode
- Multimeter
- Resistor x 4
- Zener diode

### Check for understanding

Each student finishes "Part markings" on their own, without opening the hints. The simulator checks 7 of its 7 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Glass or black: read the number".

Chapter 7. About 40 min

## Boss build

Sort a bin, fix a blinker, make it yours.

Lesson | Time | What students do

Boss: sort a parts bin Five unlabeled parts in five testers and a 555 blinker built from the wrong drawers: identify the bin, fix the transistor, the timing cap and the LED resistor, then make it blink faster in your own color. | 40 min

- Sort the bin
- The wrong transistor
- The wrong capacitor
- The wrong resistor
- Make it faster
- Make it yours: the blue LED

### Materials

- Capacitor x 2
- Component tester x 5
- DC voltage source
- Diode
- LED x 2
- NE555 timer
- Resistor x 5
- Transistor (NPN or PNP) x 2

### Check for understanding

Each student finishes "Boss: sort a parts bin" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Make it yours: the blue LED".

Your class

## Teach this unit as a class

Start a class from this course and its 7 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.

Start a class from this course See the demo class

More units

## Other lesson plans

Electronics basics 20 lessons, about 10 h. Embedded on the Arduino Uno 16 lessons, about 12 h. Embedded on the ESP32-C3 13 lessons, about 11 h. Embedded on the Raspberry Pi Pico 7 lessons, about 6 h. Build your own fight stick 5 lessons, about 4 h. Embedded on the STM32F411 6 lessons, about 6 h. C++ on a board 13 lessons, about 10 h. Digital logic and memory 4 lessons, about 4 h. Interactive devices on the Uno 9 lessons, about 8 h. From gates to a computer 23 lessons, about 16 h. Build a claw machine 8 lessons, about 6 h. Every unit All the courses as ready-made units, on the teachers page.
