Source: https://mokxi.com/teachers/plans/electric-machines-dc
Updated: 2026-11-19

Lesson plan

# DC motors and generators lesson plan

The brushed DC machine as a component: torque from current, back EMF, the torque-speed line, generator mode, where the watts go, three ways to brake, and an Uno motor dyno you build yourself.

7 chapters, 7 lessons, about 5 hours, no board. Every lesson runs in the browser, with nothing to install.

Start a class from this course

The unit

## Objectives and materials

### By the end, students can

- Torque is current, from stall to free running.
- A spinning motor pushes back, in proportion to speed.
- Free speed, stall and free current, and the line between.
- The same machine driving a load.
- Power in, copper loss and shaft power.
- Coast, dynamic braking and plugging.
- An Uno motor dyno that measures a real motor.

### Materials for the whole unit

- Arduino Uno R3
- Bench power supply
- Current monitor, INA219
- DC motor
- DC voltage source
- Gear motor with encoder
- Motor driver, L9110S
- Oscilloscope
- Resistor x 2
- Slide switch

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 50 min

## Torque and current

Torque is current, from stall to free running.

Lesson | Time | What students do

Torque and current A motor's torque is its current times a constant: a stalled motor at 1.2 V that cannot beat its friction, the start at 2 V, full speed at 6 V, the inrush at switch-on, and a lower-resistance winding that pulls twice the amps. | 50 min

- Run it: stalled
- It starts
- Full speed
- The inrush
- Running current
- A fatter winding

### Materials

- Bench power supply
- DC motor
- DC voltage source
- Oscilloscope
- Resistor x 2
- Slide switch

### Check for understanding

Each student finishes "Torque and current" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A fatter winding".

Chapter 2. About 45 min

## Back EMF

A spinning motor pushes back, in proportion to speed.

Lesson | Time | What students do

Back EMF A spinning motor is a generator pushing back: speed proportional to voltage, the voltage it makes when the supply is cut, the constant that links them, and why the running current is so small. | 45 min

- Run it: half voltage
- Cut the supply
- Proportional to speed
- Why the current is small
- A better motor

### Materials

- Bench power supply
- DC motor
- DC voltage source
- Oscilloscope
- Resistor x 2
- Slide switch

### Check for understanding

Each student finishes "Back EMF" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A better motor".

Chapter 3. About 50 min

## Motor curves

Free speed, stall and free current, and the line between.

Lesson | Time | What students do

Motor curves Read a real motor's numbers off the bench: free speed, stall current and free current of a TT gear motor, the straight-line torque-speed curve they define, and a hobby motor that spins at twelve thousand rpm. | 50 min

- Run it: a TT gear motor
- Stall current
- Free current
- Draw the curve
- A 130 hobby motor
- A better gearmotor

### Materials

- Bench power supply
- DC motor
- DC voltage source
- Oscilloscope
- Resistor x 2
- Slide switch

### Check for understanding

Each student finishes "Motor curves" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A better gearmotor".

Chapter 4. About 35 min

## Generator mode

The same machine driving a load.

Lesson | Time | What students do

Generator mode The same machine run backward: a spinning motor driving current into a load, terminal voltage against load, the matched load that takes the most power, and the energy it is spending as it slows. | 35 min

- Run it: a light load
- A heavy load
- The matched load
- Load slows it

### Materials

- Bench power supply
- DC motor
- DC voltage source
- Oscilloscope
- Resistor x 2
- Slide switch

### Check for understanding

Each student finishes "Generator mode" on their own, without opening the hints. The simulator checks 4 of its 4 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Load slows it".

Chapter 5. About 45 min

## Efficiency

Power in, copper loss and shaft power.

Lesson | Time | What students do

Efficiency Where the watts go: input power, copper loss in the winding, and the rest turned into shaft power, at full and half voltage, and what a better motor saves. | 45 min

- Run it: power in
- Copper loss
- Half voltage costs efficiency
- Work out the table
- A better motor

### Materials

- Bench power supply
- DC motor
- DC voltage source
- Oscilloscope
- Resistor x 2
- Slide switch

### Check for understanding

Each student finishes "Efficiency" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A better motor".

Chapter 6. About 35 min

## Braking

Coast, dynamic braking and plugging.

Lesson | Time | What students do

Braking Three ways to stop a motor: coast, dynamic braking with a short or a resistor, and plugging with a reversed supply that stops it and spins it the other way. | 35 min

- Run it: coast
- Dynamic braking
- Plugging
- It reverses

### Materials

- Bench power supply
- DC motor
- DC voltage source
- Oscilloscope
- Resistor x 2
- Slide switch

### Check for understanding

Each student finishes "Braking" on their own, without opening the hints. The simulator checks 4 of its 4 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "It reverses".

Chapter 7. About 45 min

## Boss build

An Uno motor dyno that measures a real motor.

Lesson | Time | What students do

Boss: characterize a motor An Uno, an L9110S, an INA219 and an encoder gear motor become a motor dyno: sweep the PWM, find the dead band, the free speed, the free current and the back EMF constant, then change the supply, prove the speed follows, find the driver's limit, and brake it. | 45 min

- Run it: the dyno
- Sweep it
- Read the numbers
- Change the supply
- Brake it

### Materials

- Arduino Uno R3
- Bench power supply
- Current monitor, INA219
- Gear motor with encoder
- Motor driver, L9110S

### Check for understanding

Each student finishes "Boss: characterize a motor" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Brake it".

Your class

## Teach this unit as a class

Start a class from this course and its 7 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.

Start a class from this course See the demo class

More units

## Other lesson plans

Electronics basics 20 lessons, about 10 h. Embedded on the Arduino Uno 16 lessons, about 12 h. Embedded on the ESP32-C3 13 lessons, about 11 h. Embedded on the Raspberry Pi Pico 7 lessons, about 6 h. Build your own fight stick 5 lessons, about 4 h. Embedded on the STM32F411 6 lessons, about 6 h. C++ on a board 13 lessons, about 10 h. Digital logic and memory 4 lessons, about 4 h. Interactive devices on the Uno 9 lessons, about 8 h. From gates to a computer 23 lessons, about 16 h. Build a claw machine 8 lessons, about 6 h. Every unit All the courses as ready-made units, on the teachers page.
