Source: https://mokxi.com/teachers/plans/control-circuit-troubleshooting
Updated: 2026-11-19

Lesson plan

# Troubleshooting control circuits lesson plan

The motor starter an industrial electrician gets called to: read the ladder, find opens with the voltage method and hopscotch, tell coils from contacts, handle overloads and intermittents, and fix a dead conveyor with three faults on it.

7 chapters, 7 lessons, about 6 hours, no board. Every lesson runs in the browser, with nothing to install.

Start a class from this course

The unit

## Objectives and materials

### By the end, students can

- Rails, rungs, wire numbers, and where 24 V should be.
- Measure across each device: the open reads the whole supply.
- One lead on L2, the other hopping until the voltage vanishes.
- An open coil, a burnt contact under load, and a welded one.
- Read a trip, set the dial from the motor, never reset into a jam.
- Why a blink is a stop, the wiggle test and the loose terminal.
- Three faults, one dangerous, and a pull-cord stop to finish.

### Materials for the whole unit

- Bench power supply
- Capacitor
- DC motor
- DPDT relay x 3
- Limit switch, lever microswitch x 3
- Multimeter x 2
- Pushbutton
- Resistor x 2
- Slide switch x 2

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 50 min

## Reading the ladder

Rails, rungs, wire numbers, and where 24 V should be.

Lesson | Time | What students do

Reading the ladder A 24 V conveyor starter drawn as a ladder: rails, rungs, wire numbers, a coil and its contacts. Run it, start it, stop it, and read where the voltage sits on each wire. | 50 min

- Run it: the bench
- Press START
- Wire 3 stays alive
- Press STOP: wire 2 goes dead
- The load takes it all
- Read it like a drawing

### Materials

- Bench power supply
- Capacitor
- DC motor
- DPDT relay x 3
- Limit switch, lever microswitch x 2
- Multimeter
- Pushbutton
- Resistor
- Slide switch

### Check for understanding

Each student finishes "Reading the ladder" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Read it like a drawing".

Chapter 2. About 50 min

## The voltage method

Measure across each device: the open reads the whole supply.

Lesson | Time | What students do

The voltage method The conveyor will not start. Measure across each device on the dead rung: closed ones read nothing, the coil reads nothing because no current flows, and the open reads the whole supply. | 50 min

- The ticket: power first
- Across a closed contact
- Across the coil: nothing
- Across the open: everything
- Fix it
- Verify

### Materials

- Bench power supply
- Capacitor
- DC motor
- DPDT relay x 3
- Limit switch, lever microswitch x 2
- Multimeter
- Pushbutton
- Resistor
- Slide switch

### Check for understanding

Each student finishes "The voltage method" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Verify".

Chapter 3. About 50 min

## Hopscotch testing

One lead on L2, the other hopping until the voltage vanishes.

Lesson | Time | What students do

Hopscotch testing One lead parked on L2, the other hopping from wire number to wire number along the rung. Voltage is there until you jump past the open; then it is gone. | 50 min

- Park one lead
- Hop to wire 2
- Through START
- The voltage vanishes
- Fix wire 3
- Verify by hopping

### Materials

- Bench power supply
- Capacitor
- DC motor
- DPDT relay x 3
- Limit switch, lever microswitch x 2
- Multimeter
- Pushbutton
- Resistor
- Slide switch

### Check for understanding

Each student finishes "Hopscotch testing" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Verify by hopping".

Chapter 4. About 50 min

## Failed coils and contacts

An open coil, a burnt contact under load, and a welded one.

Lesson | Time | What students do

Failed coils and contacts A coil with 24 V across it that never pulls in, then a contactor that runs the motor slow: an open coil proved on the ohms range, and a burnt contact found by measuring it under load. | 50 min

- Full voltage, no click
- Lock out, ohm it, replace it
- It runs, slowly
- Measure the contact under load
- New contacts
- The other contact failure: welded

### Materials

- Bench power supply
- Capacitor
- DC motor
- DPDT relay x 3
- Limit switch, lever microswitch x 2
- Multimeter
- Pushbutton
- Resistor x 2
- Slide switch

### Check for understanding

Each student finishes "Failed coils and contacts" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "The other contact failure: welded".

Chapter 5. About 50 min

## Overloads

Read a trip, set the dial from the motor, never reset into a jam.

Lesson | Time | What students do

Overloads An overload that trips the instant START is pressed, then a jam that trips it for real. Read the trip, set the dial from the motor's current, measure the running amps, and never reset into a jam. | 50 min

- Tripped on start
- Read the dial
- Measure the running current
- Jam the belt
- Clear it, then reset
- Setting a real overload

### Materials

- Bench power supply
- Capacitor
- DC motor
- DPDT relay x 3
- Limit switch, lever microswitch x 2
- Multimeter x 2
- Pushbutton
- Resistor
- Slide switch

### Check for understanding

Each student finishes "Overloads" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Setting a real overload".

Chapter 6. About 55 min

## Intermittents

Why a blink is a stop, the wiggle test and the loose terminal.

Lesson | Time | What students do

Intermittents A conveyor that stops on its own once a shift and runs fine when you get there. Why a split-second open stops a seal-in circuit for good, the wiggle test, and catching the loose terminal on the meter. | 55 min

- Runs fine when you look
- Why a blink is a stop
- Catch it on the meter
- Hop past it
- Terminate it properly
- Prove it with a wiggle
- The usual suspects

### Materials

- Bench power supply
- Capacitor
- DC motor
- DPDT relay x 3
- Limit switch, lever microswitch x 2
- Multimeter
- Pushbutton
- Resistor
- Slide switch x 2

### Check for understanding

Each student finishes "Intermittents" on their own, without opening the hints. The simulator checks 7 of its 7 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "The usual suspects".

Chapter 7. About 1 h 5 min

## Boss: fix a dead conveyor

Three faults, one dangerous, and a pull-cord stop to finish.

Lesson | Time | What students do

Boss: fix a dead conveyor A repair ticket on the packing line: the conveyor is dead. Three faults stand between you and a running belt, one of them dangerous. Find each with the meter, fix it, verify, then add a pull-cord stop. | 65 min

- The ticket
- Fault 1: find the open
- Fix wire 4
- Fault 2: runs only while held
- Verify the latch
- Fault 3: STOP does not stop
- Remove the jumper
- Make it yours: a pull-cord stop

### Materials

- Bench power supply
- Capacitor
- DC motor
- DPDT relay x 3
- Limit switch, lever microswitch x 3
- Multimeter
- Pushbutton
- Resistor
- Slide switch

### Check for understanding

Each student finishes "Boss: fix a dead conveyor" on their own, without opening the hints. The simulator checks 8 of its 8 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Make it yours: a pull-cord stop".

Your class

## Teach this unit as a class

Start a class from this course and its 7 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.

Start a class from this course See the demo class

More units

## Other lesson plans

Electronics basics 20 lessons, about 10 h. Embedded on the Arduino Uno 16 lessons, about 12 h. Embedded on the ESP32-C3 13 lessons, about 11 h. Embedded on the Raspberry Pi Pico 7 lessons, about 6 h. Build your own fight stick 5 lessons, about 4 h. Embedded on the STM32F411 6 lessons, about 6 h. C++ on a board 13 lessons, about 10 h. Digital logic and memory 4 lessons, about 4 h. Interactive devices on the Uno 9 lessons, about 8 h. From gates to a computer 23 lessons, about 16 h. Build a claw machine 8 lessons, about 6 h. Every unit All the courses as ready-made units, on the teachers page.
