Source: https://mokxi.com/teachers/plans/build-rotary-phone-jukebox
Updated: 2026-11-19

Lesson plan

# Build a rotary phone jukebox lesson plan

Read a rotary dial pulse by pulse, add a hook switch and a DFPlayer, and turn an old phone into a jukebox that rings you back.

3 chapters, 6 lessons, about 5 hours, on the Arduino Uno R3. Every lesson runs in the browser, with nothing to install.

Start a class from this course

The unit

## Objectives and materials

### By the end, students can

- Time the pulses of a rotary dial and count them into numbers.
- The hook switch, the dial tone and an MP3 player on a serial link.
- A ringing bell and a phone that plays the song you dial.

### Materials for the whole unit

- Arduino Uno R3
- Buzzer
- DFPlayer Mini MP3 module
- Half breadboard
- Limit switch, lever microswitch
- Resistor
- Rotary dial

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 1 h 30 min

## Dialing

Time the pulses of a rotary dial and count them into numbers.

Lesson | Time | What students do

Pulse dialing Read a rotary dial the way the telephone exchange did: ten pulses a second, each a 60 ms break and a 40 ms make, timed one by one. | 50 min

- A phone from 1970
- Off normal
- Break
- Make
- Ten for zero

Counting digits Count pulses into digits and digits into a number, using the gap between digits as the separator and a three-second pause to finish. | 40 min

- Count the breaks
- Zero again
- A whole number
- Read the dial

### Materials

- Arduino Uno R3
- Buzzer
- DFPlayer Mini MP3 module
- Half breadboard
- Limit switch, lever microswitch
- Resistor
- Rotary dial

### Check for understanding

Each student finishes "Counting digits" on their own, without opening the hints. The simulator checks 4 of its 4 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Read the dial".

Chapter 2. About 1 h 40 min

## The phone

The hook switch, the dial tone and an MP3 player on a serial link.

Lesson | Time | What students do

The hook switch Add the hook switch: a dial tone when the handset is lifted, dialing ignored on hook, and the call over the moment it is hung up. | 50 min

- Off the hook
- Dial tone
- Hang up
- Dialing on hook
- Make a call

MP3 tracks Drive a DFPlayer Mini over a serial link: dial a digit to play that track, get a busy signal for one that is not there, and stop the music by hanging up. | 50 min

- Twelve songs
- Dial a track
- What is playing
- Busy signal
- Hang up the music

### Materials

- Arduino Uno R3
- Buzzer
- DFPlayer Mini MP3 module
- Half breadboard
- Limit switch, lever microswitch
- Resistor
- Rotary dial

### Check for understanding

Each student finishes "MP3 tracks" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Hang up the music".

Chapter 3. About 1 h 40 min

## The jukebox

A ringing bell and a phone that plays the song you dial.

Lesson | Time | What students do

Ring sounds Make the phone ring back: dial the operator, hang up, and hear a 20 Hz bell in the two-on, four-off cadence until you answer. | 50 min

- Call the operator
- It rings
- Twenty times a second
- Answer it
- Nobody home

Project: dial a song Run the whole jukebox: one- and two-digit song numbers, the dial tone back when a song ends, busy signals, ring-backs, and a phone of your own. | 50 min

- Jukebox ready
- Song twelve
- Song over
- Wrong number
- Build your phone

### Materials

- Arduino Uno R3
- Buzzer
- DFPlayer Mini MP3 module
- Half breadboard
- Limit switch, lever microswitch
- Resistor
- Rotary dial

### Check for understanding

Each student finishes "Project: dial a song" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Build your phone".

Your class

## Teach this unit as a class

Start a class from this course and its 6 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.

Start a class from this course See the demo class

More units

## Other lesson plans

Electronics basics 20 lessons, about 10 h. Embedded on the Arduino Uno 16 lessons, about 12 h. Embedded on the ESP32-C3 13 lessons, about 11 h. Embedded on the Raspberry Pi Pico 7 lessons, about 6 h. Build your own fight stick 5 lessons, about 4 h. Embedded on the STM32F411 6 lessons, about 6 h. C++ on a board 13 lessons, about 10 h. Digital logic and memory 4 lessons, about 4 h. Interactive devices on the Uno 9 lessons, about 8 h. From gates to a computer 23 lessons, about 16 h. Build a claw machine 8 lessons, about 6 h. Every unit All the courses as ready-made units, on the teachers page.
