Source: https://mokxi.com/teachers/plans/build-reflow-oven
Updated: 2026-11-19

Lesson plan

# Build a reflow oven controller lesson plan

Build the low-voltage side of a reflow oven: a thermocouple, an SSR, solder profiles, PID tracking and the safety cutoffs that make it trustworthy.

3 chapters, 6 lessons, about 6 hours, on the Arduino Uno R3. Every lesson runs in the browser, with nothing to install.

Start a class from this course

The unit

## Objectives and materials

### By the end, students can

- A thermocouple in, a solid-state relay out.
- Solder profiles, then PID to track them.
- Cutoffs that fail safe, then a full run.

### Materials for the whole unit

- Arduino Uno R3
- Battery: AA, coin cell, LiPo
- Buzzer
- Filament lamp
- Full-size breadboard
- Slide switch
- Solid-state relay, SSR-25DA / G3MB-202P
- Thermocouple converter, MAX6675

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 2 h

## Measure and switch

A thermocouple in, a solid-state relay out.

Lesson | Time | What students do

Thermocouples Measure an oven with a type K thermocouple and a MAX6675: the microvolts at the tip, the cold junction they are measured against, quarter degree steps and an open probe. | 60 min

- Safety first
- Microvolts and a cold junction
- Reflow heat
- Quarter degrees
- A broken probe

SSR control Drive a solid-state relay from a pin, learn why zero-cross SSRs cannot be dimmed, and control power by switching for part of each one second window. | 60 min

- No contacts
- Forty percent
- The SSR conducts
- The heater glows
- Off means off

### Materials

- Arduino Uno R3
- Battery: AA, coin cell, LiPo
- Buzzer
- Filament lamp
- Full-size breadboard
- Slide switch
- Solid-state relay, SSR-25DA / G3MB-202P
- Thermocouple converter, MAX6675

### Check for understanding

Each student finishes "SSR control" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Off means off".

Chapter 2. About 2 h

## Follow the profile

Solder profiles, then PID to track them.

Lesson | Time | What students do

Profiles Follow a solder profile on a simulated oven: preheat, soak, reflow above the liquidus to the peak, and cool, for lead-free and leaded paste. | 60 min

- A recipe in temperatures
- Preheat and soak
- Reflow
- Done, with on/off control
- Leaded paste

PID tracking Track the profile with PID and feed-forward instead of on/off, and compare the overshoot, the time above liquidus and the worst error. | 60 min

- Three terms
- The peak
- Proportional power
- Compare
- Leaded, with PID

### Materials

- Arduino Uno R3
- Battery: AA, coin cell, LiPo
- Buzzer
- Filament lamp
- Full-size breadboard
- Slide switch
- Solid-state relay, SSR-25DA / G3MB-202P
- Thermocouple converter, MAX6675

### Check for understanding

Each student finishes "PID tracking" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Leaded, with PID".

Chapter 3. About 2 h 10 min

## Make it safe

Cutoffs that fail safe, then a full run.

Lesson | Time | What students do

Safety cutoffs Ring the controller with cutoffs that all fail safe: overtemp, a thermocouple fault, an open door, and a heater that does not warm the oven. | 60 min

- Hold at 150
- Overtemp
- A broken probe
- The door
- No rise

Project: a solder profile The finished controller: pick a paste, track its profile with PID, watch the door and the thermocouple every pass, and finish with a summary and a beep. | 70 min

- Load the board
- A full run
- The door mid-run
- A probe fault mid-run
- Your paste
- Before a real oven

### Materials

- Arduino Uno R3
- Battery: AA, coin cell, LiPo
- Buzzer
- Filament lamp
- Full-size breadboard
- Slide switch
- Solid-state relay, SSR-25DA / G3MB-202P
- Thermocouple converter, MAX6675

### Check for understanding

Each student finishes "Project: a solder profile" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Before a real oven".

Your class

## Teach this unit as a class

Start a class from this course and its 6 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.

Start a class from this course See the demo class

More units

## Other lesson plans

Electronics basics 20 lessons, about 10 h. Embedded on the Arduino Uno 16 lessons, about 12 h. Embedded on the ESP32-C3 13 lessons, about 11 h. Embedded on the Raspberry Pi Pico 7 lessons, about 6 h. Build your own fight stick 5 lessons, about 4 h. Embedded on the STM32F411 6 lessons, about 6 h. C++ on a board 13 lessons, about 10 h. Digital logic and memory 4 lessons, about 4 h. Interactive devices on the Uno 9 lessons, about 8 h. From gates to a computer 23 lessons, about 16 h. Build a claw machine 8 lessons, about 6 h. Every unit All the courses as ready-made units, on the teachers page.
