Source: https://mokxi.com/teachers/plans/build-led-sign
Updated: 2026-11-19

Lesson plan

# Build a scrolling LED sign lesson plan

Four chained LED matrices driven bit by bit, your own 5x7 font, smooth scrolling, typed messages, auto brightness and an on-air sign.

3 chapters, 6 lessons, about 5 hours, on the Arduino Uno R3. Every lesson runs in the browser, with nothing to install.

Start a class from this course

The unit

## Objectives and materials

### By the end, students can

- Drive a chain of four MAX7219s by hand and draw with a font made of bytes.
- A strip of columns, a moving window and messages from the serial port.
- Brightness that follows the room, and a sign for the studio door.

### Materials for the whole unit

- Arcade button
- Arduino Uno R3
- LED matrix, 8x8
- Photoresistor sensor module

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 1 h 30 min

## Matrices and fonts

Drive a chain of four MAX7219s by hand and draw with a font made of bytes.

Lesson | Time | What students do

Chained matrices Drive four MAX7219 chips in a daisy chain by hand: wake them, run a display test of all 256 LEDs, and light one module at a time with No-Op packets. | 45 min

- Four chips, one chain
- Display test
- Down the chain
- One module, 64 LEDs

Fonts Store a 5x7 font as bytes in flash, draw a word with it, and see every character as hex and as a picture of its pixels. | 45 min

- A font is bytes
- Look inside an A
- Draw it in text
- Count the pixels

### Materials

- Arcade button
- Arduino Uno R3
- LED matrix, 8x8
- Photoresistor sensor module

### Check for understanding

Each student finishes "Fonts" on their own, without opening the hints. The simulator checks 4 of its 4 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Count the pixels".

Chapter 2. About 1 h 45 min

## Scrolling and messages

A strip of columns, a moving window and messages from the serial port.

Lesson | Time | What students do

Scrolling Turn a message into one long strip of columns, slide a 32-column window along it on a timer, and change the speed while it runs. | 45 min

- Hello, world
- How long is the strip?
- Round and round
- Faster

Messages Take new messages typed over serial, swap them in at the end of a pass, tidy the input, and see how the same code takes them over WiFi on an ESP32. | 60 min

- Your words
- Send one
- At the end of the pass
- Tidy input
- Too long

### Materials

- Arcade button
- Arduino Uno R3
- LED matrix, 8x8
- Photoresistor sensor module

### Check for understanding

Each student finishes "Messages" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Too long".

Chapter 3. About 1 h 45 min

## On air

Brightness that follows the room, and a sign for the studio door.

Lesson | Time | What students do

Brightness Set the sign's brightness from a light sensor: average eight readings, map them to the chip's sixteen steps, dim at night and bright in the sun. | 45 min

- Follow the room
- Lights out
- Full sun
- Still listening

Project: an on-air sign Put it all together: scrolling messages and automatic brightness, and a red button that puts a steady ON AIR on the sign at full brightness. | 60 min

- Quiet please
- Go live
- Eighty LEDs
- Off air
- Hang it on the door

### Materials

- Arcade button
- Arduino Uno R3
- LED matrix, 8x8
- Photoresistor sensor module

### Check for understanding

Each student finishes "Project: an on-air sign" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Hang it on the door".

Your class

## Teach this unit as a class

Start a class from this course and its 6 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.

Start a class from this course See the demo class

More units

## Other lesson plans

Electronics basics 20 lessons, about 10 h. Embedded on the Arduino Uno 16 lessons, about 12 h. Embedded on the ESP32-C3 13 lessons, about 11 h. Embedded on the Raspberry Pi Pico 7 lessons, about 6 h. Build your own fight stick 5 lessons, about 4 h. Embedded on the STM32F411 6 lessons, about 6 h. C++ on a board 13 lessons, about 10 h. Digital logic and memory 4 lessons, about 4 h. Interactive devices on the Uno 9 lessons, about 8 h. From gates to a computer 23 lessons, about 16 h. Build a claw machine 8 lessons, about 6 h. Every unit All the courses as ready-made units, on the teachers page.
