Source: https://mokxi.com/teachers/plans/build-bench-tools
Updated: 2026-11-19

Lesson plan

# Build your own bench tools lesson plan

A frequency counter, a capacitance meter, a resistor tester, a battery tester and a DAC signal generator, then all five in one LCD box.

3 chapters, 6 lessons, about 5 hours, on the Arduino Uno R3. Every lesson runs in the browser, with nothing to install.

Start a class from this course

The unit

## Objectives and materials

### By the end, students can

- Count edges in a gate and time a capacitor charging.
- Resistors by divider and batteries by the milliamp-hour.
- A DAC that makes voltages, then all five tools in one box.

### Materials for the whole unit

- Arduino Uno R3
- Battery: AA, coin cell, LiPo
- Capacitor
- Character LCD with I2C backpack
- Current monitor, INA219
- DAC, MCP4725
- Function generator
- Pushbutton
- Resistor x 4

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 1 h 40 min

## Measure time

Count edges in a gate and time a capacitor charging.

Lesson | Time | What students do

A frequency counter Count the rising edges of a signal for exactly one second with an interrupt, and see how the gate sets the resolution and where the meter stops being right. | 55 min

- A bench on one board
- Count for one second
- Turn the dial
- Mains hum
- Too slow to count
- Too fast to trust

A capacitance meter Charge a capacitor through 10k, time how long it takes to reach 63.2% of the supply, and that time is R x C: a capacitance meter from one resistor and a stopwatch. | 45 min

- Measure a capacitor
- The time constant
- Empty before you measure
- Small capacitors
- Too big to wait for

### Materials

- Arduino Uno R3
- Battery: AA, coin cell, LiPo
- Capacitor
- Character LCD with I2C backpack
- Current monitor, INA219
- DAC, MCP4725
- Function generator
- Pushbutton
- Resistor x 4

### Check for understanding

Each student finishes "A capacitance meter" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Too big to wait for".

Chapter 2. About 1 h 30 min

## Parts and power

Resistors by divider and batteries by the milliamp-hour.

Lesson | Time | What students do

A component tester Read an unknown resistor with a known 10k and the ADC, work out its color bands, and see why a two-resistor meter is sharp in the middle and blunt at the ends. | 45 min

- Ohms from a divider
- Read the bands
- A 220 ohm resistor
- Blunt at the ends
- Nothing there

A battery tester Run an AA cell into a 10 ohm load through an INA219, add up the milliamp-hours every second, and stop at 0.9 V with the capacity it really delivered. | 45 min

- A cell under load
- Volts and milliamps
- Add it up
- Spent
- A real AA

### Materials

- Arduino Uno R3
- Battery: AA, coin cell, LiPo
- Capacitor
- Character LCD with I2C backpack
- Current monitor, INA219
- DAC, MCP4725
- Function generator
- Pushbutton
- Resistor x 4

### Check for understanding

Each student finishes "A battery tester" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "A real AA".

Chapter 3. About 1 h 40 min

## Signals and the box

A DAC that makes voltages, then all five tools in one box.

Lesson | Time | What students do

A signal generator Set any voltage from 0 to 5 V in 1.2 mV steps with an MCP4725 DAC, then step a 32-point sine table out of it at 5 Hz. | 45 min

- A real analog output
- Ask for 2.5 V
- Measure it
- Odd voltages
- A sine from a table

One box, five tools Put all five instruments behind one 16x2 LCD and a MENU button: frequency, capacitance, resistance, battery and a DAC staircase, the same numbers as the lessons before. | 55 min

- The box
- FREQ
- CAP and OHMS
- BATT
- DAC
- Make it yours

### Materials

- Arduino Uno R3
- Battery: AA, coin cell, LiPo
- Capacitor
- Character LCD with I2C backpack
- Current monitor, INA219
- DAC, MCP4725
- Function generator
- Pushbutton
- Resistor x 4

### Check for understanding

Each student finishes "One box, five tools" on their own, without opening the hints. The simulator checks 6 of its 6 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Make it yours".

Your class

## Teach this unit as a class

Start a class from this course and its 6 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.

Start a class from this course See the demo class

More units

## Other lesson plans

Electronics basics 20 lessons, about 10 h. Embedded on the Arduino Uno 16 lessons, about 12 h. Embedded on the ESP32-C3 13 lessons, about 11 h. Embedded on the Raspberry Pi Pico 7 lessons, about 6 h. Build your own fight stick 5 lessons, about 4 h. Embedded on the STM32F411 6 lessons, about 6 h. C++ on a board 13 lessons, about 10 h. Digital logic and memory 4 lessons, about 4 h. Interactive devices on the Uno 9 lessons, about 8 h. From gates to a computer 23 lessons, about 16 h. Build a claw machine 8 lessons, about 6 h. Every unit All the courses as ready-made units, on the teachers page.
